深海变径声阵缆布放回收装置研究

本文提出了基于深海工作站运搭载的变径缆海底布放回收方式，介绍了变径缆海底布放回收装置的主要工作原理和结构组成，完成了布放回收装置主要部套件的设计计算以及和电液控制系统的设计及计算。     

基于自适应活动轮廓的图像分割

在活 动轮廓的基础上，引入了统计“图像势能”和松驰法，提出了基于自适应活动轮廓的图像分 割方法。该方法克服了活动轮廓的一些缺陷，能准确、可靠地检测物体曲率高的边缘部分，且分割结果与活动轮廓的初始位置无关。实验结果验证了该方法的有效性。     

S^2 BHCA Multiple AUVs cooperation oriented control architecture

Oceanographic survey, or other similar applications should be the applications of multiple AUVs. In this paper, the skill ＆ simulation based hybrid control architecture （S^2BHCA） as the controller＇s design reference was proposed. It is a multi-robot cooperation oriented intelligent control architecture based on hybrid ideas. The S^2BHCA attempts to incorporate the virtues of the reactive controller and of the deliberative controller by introducing the concept of the ＂skill＂. The additional online task simulation ability for cooperation is supported, too. As an application, a multiple AUV control system was developed with three ＂skills＂ for the MCM mission including two different cooperative tasks. The simulation and the sea trials show that simple task expression, fast reaction and better cooperation support can be achieved by realizing the AUV controller based on the S^2BHCA.     

烟大铁路轮渡渡船电力推进系统仿真分析

随着计算机仿真技术在工程研究领域的广泛应用,船舶电力系统数字仿真已成为高效的船舶电力系统分析手段.烟大火车渡船采用了当今国际先进的电力推进系统,通过对该系统进行了数字仿真分析,验证了该船电网运行的稳定性和可靠性.     

多功能智能型航次计划优化系统设计与实现

介绍了一个多功能智能型航次计划优化系统的设计与实现，得到了一个能在微机网络上运行的有效原型。在设计中引入了人工智能技术，并特别注意了友好的人机界面。     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

大口径超深钻孔灌注桩施工

录安洲夹江大桥基础采用超深钻孔灌注桩,由于桩径大,地质复杂,施工难度较大。文章介绍在施工中采取先进施工方法,并针对在施工过程中出现的一系列问题及采取的相应对策,成功地完成了施工任务。     

成南高速公路岩质高边坡绿化实践

以成南高速公路K73路段高边坡的绿化为例,介绍岩质边坡的绿化方法,说明边坡绿色防护具有良好的社会效益、经济效益与工程效果。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)