New Optimal Power Management Strategy for Series Plug-In Hybrid Electric Vehicles

Recently Plug-in hybrid electric vehicles (PHEVs) have gained increasing attention due to their ability to reduce the fuel consumption and emissions. In this paper a new efficient power management strategy is proposed for a series PHEV. According to the battery state of charge (SOC) and vehicle power requirement, a new rule-based optimal power controller with four different operating modes is designed to improve the fuel economy of the vehicle. Furthermore, the teaching-learning based optimization (TLBO) method is employed to find the optimal engine power and battery power under the specified driving cycle while the fuel consumption is considered as the fitness function. In order to demonstrate the effectiveness of the proposed method, four different driving cycles with various numbers of driving distances for each driving cycle are selected for the simulation study. The performance of the proposed optimal power management strategy is compared with the rule-based power management method. The results verify that the proposed power management method could significantly improve the fuel economy of the series PHEV for different driving conditions.     

A Solution Processable Flexible Transparent Conductive Graphene/PEDOT: PSS Film Fabricated by Spin and Blade Coating

Flexible transparent conductive films were made on PET substrates by spin and blade coating, using graphene sheets dispersed in PEDOT: PSS solution. Ultrasonic substrate vibration was used to improve microstructure and properties of the films. Comparing to the pristine PEDOT: PSS film, the sheet resistance is 3 to 4 orders of magnitude lower with the addition of graphene. The conductivity and reproducibility of the film are improved for two-layer films comparing to one-layer films, with a reduction in transparency. Films prepared with substrate vibration showed lower sheet resistance for one-layer films, as the size of dewetting areas is reduced. In addition, large-area flexible films with desirable conductivity and transmittance were successfully fabricated by blade coating, which is promising, as the process is low-cost, scalable and compatible with roll-to-roll manufacturing.     

槽道型高速滑行艇船型的自动生成(英文)

The creation of geometric model of a ship to determine the characteristics of hydrostatic and hydrodynamic, and also for structural design and equipments arrangement are so important in the ship design process. Planning tunnel high speed craft is one of the crafts in which, achievement to their top speed is more important. These crafts with the use of tunnel have the aero-hydrodynamics properties to diminish the resistance, good sea-keeping behavior, reduce slamming and avoid porpoising. Because of the existence of the tunnel, the hull form generation of these crafts is more complex and difficult. In this paper, it has attempted to provide a method based on geometry creation guidelines and with an entry of the least control and hull form adjustment parameters, to generate automatically the hull form of planning tunnel craft. At first, the equations of mathematical model are described and subsequent, three different models generated based on present method are compared and analyzed. Obviously, the generated model has more application in the early stages of design.     

Understanding Spray Coating Process: Visual Observation of Impingement of Multiple Droplets on a Substrate

Spray coating is a facile deposition process with numerous existing and emerging applications. However, spray coating is a stochastic process comprising impingement of many droplets which upon impact on a heated substrate may dry or solidify individually or coalesce first to form a thin liquid film and then dry to yield a thin solid film. There is very limited knowledge on how this process occurs; therefore in this work, high speed imaging is used to visualize the spray coating process. Two model solutions including food-dye with properties like those of water, and poly (3, 4-ethylenedioxythiophene): poly (styrenesulfonate) (PEDOT:PSS), a polymeric solution, are sprayed onto permeable glossy paper and regular impermeable glass substrates. Substrates are kept at room temperature and 80 °C elevated temperature. In some cases, a vertical ultrasonic vibration is imposed on the substrate to study its effect on the coating process. It is observed that the spray coating process is highly random and stochastic. A higher substrate temperature results in a better coating process in that a more uniform and defect-free coating forms. Imposed vibration in the case of glossy paper substrates results in better droplet spreading and more uniform coating. The results also show that under the conditions of these experiments, impinged droplets dry individually or as islands of multiple coalesced droplets to form a coating. In other words, at used spray flow rate and spray droplet size, a continuous thin liquid film does not form prior to drying even at room temperature. Further systematic studies and high magnification lenses are required to visualize and understand the details of the process.