兰新高铁甘青段路基冻胀自动监测及分析研究

为查明兰新高铁甘青段路基冻胀变形原因和影响因素,提出相应的冻胀处理措施,将路基冻胀变形控制在允许范围之内,采用自动监测系统,对路肩以下5 m范围内路基的冻结深度、水分、冻胀变形等进行监测,并对监测结果进行统计分析和深入研究。研究结果表明:路基冻结深度的发展主要受气温的影响,基床表层以下填料含水量随着冻结深度增加缓慢增加;基床表层及基床底层上部1.0 m范围冻胀量占总冻胀量的80%以上;低路堤地段冻胀最严重。为减少路基冻胀量,设计及施工时应采用全冻结深度防冻胀方案,以填料防冻胀为主,辅以防水、疏水和隔热等综合措施;低路堤地段防冻胀措施应适当加强。     

独柱墩-固定式防船撞装置波浪荷载研究

以跨海航道桥梁安全为背景，进行独柱墩及独柱墩-固定式防船撞装置结构波浪力研究。开展室内缩尺试验，验证并校准Fluent三维数值模型的准确性和有效性。利用最小二乘法分解墩柱水动力为Morison方程的形式，计算得到结构水动力系数。考虑波浪高度、波浪周期、防撞装置断面形状和大小等影响因素，计算并拟合出墩柱水动力系数与相关因素间的定量关系。研究结果表明：固定式防船撞装置的存在增大了墩柱表面所受波压强，但不改变其总体分布趋势。当防撞装置断面为矩形，且波浪高度较大时，装置对墩柱受力特性的影响最明显。墩柱结构所受水动力中惯性力占主导，且可用均匀分布的惯性力系数来代替实际分布，独柱墩-固定式防船撞装置结构上的惯性力系数可以达到2.1左右。     

考虑围岩蠕变特性的TBM隧道管片衬砌受力特性研究

为研究深部高地应力岩层中修建TBM隧道时管片衬砌结构的力学行为,以某深埋TBM工法隧道为研究对象,建立基于围岩蠕变和管片分块效应的衬砌-围岩复合模型,研究考虑时间效应下管片衬砌的受力特性。结果表明:考虑围岩蠕变效应下管片衬砌受力表现出明显的时间效应。随着围岩蠕变时间的延长,管片衬砌的形变、内力和接缝张开量均呈现两阶段增长,具体表现为前期呈线性增长,后期增加趋缓。洞周围岩应力经历三阶段变化,即先减小后增大直至稳定。围岩蠕变时间为100年时,管片衬砌的内力和形变量均接近极限值。研究结果可为深部高地应力且考虑围岩蠕变效应下的TBM隧道衬砌结构设计提供参考。     

重载铁路四线高墩连续梁桥的设计

神瓦(神木—瓦塘)铁路冯家川车站大桥为重载铁路四线桥,主桥采用4线(65+100+65)m连续梁,最大墩高85 m.桥上线间距大,上下部结构横向尺寸较大,利用有限元分析软件BSAS,MIDAS/FEA对结构受力进行了计算分析.结果表明:在主梁梁高相同的情况下,采用单箱三室截面能更好地减小主应力,采用单箱双室截面增加腹板厚度对主应力的改善有限;多线桥桥墩横向尺寸较大,空心截面设置纵肋板能很好地提高高墩的局部稳定性;主梁及桥墩各项计算指标均满足规范要求.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

客运专线连续梁桥墩线刚度限值探讨

研究目的:近年来,连续梁已成为新建铁路及客运专线的常用梁型。新建铁路一次性铺设跨区间之缝线路已成为趋势,研究连续梁桥上无缝线路纵向力变化规律,探讨客运专线常见连续梁桥墩线刚度限值迫在眉睫。研究结果:提出客运专线常见连续梁桥墩线刚度限值,可指导桥梁和轨道的前期设计。     

Reliability-based calibration of fatigue design guidelines for ship structures

A simple reliability-based framework is applied to calibrate a new set of fatigue design guidelines. This new guideline considers two different approaches for the assessment of both loads, stresses and local stress raising effects, and partial safety factors must be given for any combination of these approaches. For the calibration, the lognormal reliability format is adopted because the hereby-derived partial safety factors can be combined arbitrarily. This means that with a few basic partial safety factors, the combination of partial safety factors to be applied together with any combination of calculation approaches can be determined easily. In the present paper both the adopted reliability format, the applied modeling of uncertainties and the selected target safety index are explained. Based on this, a new guideline is calibrated and the derived partial safety factors are presented. Finally, the new guideline is applied through a numerical example in order to show the applicability of the calibrated partial safety factors, and satisfactory results are found.     

我国高等级公路机械化施工机械配备

高等级公路施工中，机械化程度很高，施工中机械的配备对工程的影响很大．文章结合京津塘高速公路北京段及合肥－南京－级公路安徽段工程实际施工情况，介绍了我国高等级公路施工机械的配备．     

加速发展我国高性能船舶和水上高速客运

为开发海洋经济，发展海上运输，加快海军现代化建设步伐，必须加速发展高性能船舶和水下高速客运。为此，本文提出了有关决策层参考的几点政策性建议。     

天津港突堤转角处高桩码头后承台构件相对错位破损原因

近几年天津港多个突堤转角处的高桩码头岸坡变形比较明显,导致码头后方承台结构构件出现明显的相对错位、变形等破损情况,严重影响了码头结构物安全。通过对破损状况的调查统计,总结出了破损的特点,对破损的原因进行了理论分析,并用原型观测和数模计算结果进行了验证。原型观测结果表明:码头岸坡内的淤泥质粘土层为水平位移最明显土层,靠近挡土墙的大部分桩顶都出现了不同程度的向陆侧倾斜,这与实际见到的桩端倾斜状况完全相符。数模计算结果除验证了原型观测的结果以外,还发现仅在后方堆场堆载工况为最危险情况,是造成岸坡变形和后方承台构件相对错位的主要原因。