无砟轨道板精调车结构可靠性分析及优化

为提高无砟轨道板精调车结构的设计水平,考虑精调车荷载、几何尺寸和材料弹性模量等设计变量的随机性,对精调车结构进行可靠性分析、可靠性灵敏度分析和可靠性优化。首先,分析并得到精调车结构在串联失效模式下的结构功能函数;然后,运用响应面法和重要抽样方法,分析得到基于确定性优化的精调车结构的失效概率和可靠性灵敏度结果。最后,根据可靠性灵敏度分析结果,对该结构进行可靠性优化。分析精调车结构在可靠性优化前后的差异,结果表明,与确定性优化结果相比,可靠性优化使精调车结构自重增加了3.55%,但可靠度提高为0.999 999 987 7,说明设计变量的随机性对结构性能的干扰大幅减小。     

低液限粉质粘土改良方法初探

按照一定的比例。将石灰或砂砾与低液限粉质粘土掺拌，能有效地减小低液限粉质粘土的胀缩性，具有较高的实用价值。     

多重调谐质量阻尼器对简支箱型梁结构低频振动控制的仿真研究

为了研究MTMD(多重调谐质量阻尼器)对简支箱型梁低频振动的控制特性,首先通过对箱梁结构进行模态分析确定受控模态,利用经典扩展定点理论进行TMD(调谐质量阻尼器)的最优参数设计,并基于位移振幅最小化的原则,建立评价函数分别进行MTMD的最优参数设计;进而利用有限元分析软件ANSYS进行谐响应分析,研究了TMD的设置个数对减振效果的影响,并针对阻尼器的质量改变、刚度改变和阻尼改变进行了参数敏感性分析。研究结果显示:在附加质量相同的情况下,MTMD的制振效果随着设置阻尼器个数的增加而增强,但个数增至一定程度后,减振效果的提升不再明显;MTMD在质量、刚度参数发生偏移时的制振稳定性随TMD个数的增加而减弱,阻尼参数偏移时的制振稳定性随TMD个数的增加而增强。     

沥青混凝土路面水损害的成因和预防

水损害是主要沥青路面病害之一,造成水损害的外因主要有交通量、交通组成、降雨量以及不尽完善的路面排水系统。沥青路面产生水损害的内因可以归纳为沥青混和料孔隙率过大、路面压实度不足、沥青与集料间的粘附性差以及混合料不均匀。减少沥青路面水损害的措施很多,概括起来主要有路面结构设计、沥青混合料组成设计、施工工艺三方面的措施。     

地铁环境振动预测中链式结构振级落差灵敏度分析

针对地铁环境振动预测中使用的链式结构力学简化模型,利用灵敏度分析对链式结构中各参数变化对各振级落差影响规律进行系统研究;推导给出振级落差一阶灵敏度解析表达式和一种逆矩阵偏导数求解方法;并提出利用自由衰减时域段实测数据逆求链式结构中各力学参数方法。研究结果表明:通过灵敏度分析可以确定链式结构中任一力学参数改变对其任一层振级落差影响程度,找出对系统动态响应影响较大的环节。该方法有助于提高环境振动预测精度。     

地铁盾构隧道管片设计参数的敏感性分析

以苏州地铁盾构隧道为计算原型,对设计中的关键参数进行敏感性分析,讨论设计方法、地质参数及结构参数对管片设计的影响,以及管片在水土分算与水土合算条件下受力性能的差异,并对苏州地铁盾构管片设计提出合理建议。     

Bush-based sensitivity analysis for approximating subnetwork diversion

Subnetwork analysis is often used in traffic assignment problems to reduce the size of the network being analyzed, with a corresponding decrease in computation time. This is particularly important in network design, second-best pricing, or other bilevel problems in which many equilibrium runs must be solved as a subproblem to a master optimization program. A fixed trip table based on an equilibrium path flow solution is often used, but this ignores important attraction and diversion effects as drivers (globally) change routes in response to (local) subnetwork changes. This paper presents an approach for replacing a regional network with a smaller one, containing all of the subnetwork, and zones. Artificial arcs are created to represent “all paths” between each origin and subnetwork boundary node, under the assumption that the set of equilibrium routes does not change. The primary contribution of the paper is a procedure for estimating a cost function on these artificial arcs, using derivatives of the equilibrium travel times between the end nodes to create a Taylor series. A bush-based representation allows rapid calculation of these derivatives. Two methods for calculating these derivatives are presented, one based on network transformations and resembling techniques used in the analysis of resistive circuits, and another based on iterated solution of a nested set of linear equations. These methods are applied to two networks, one small and artificial, and the other a regional network representing the Austin, Texas metropolitan area. These demonstrations show substantial improvement in accuracy as compared to using a fixed table, and demonstrate the efficiency of the proposed approach.     

缓波型非粘接柔性立管的干涉敏感性

针对非粘接柔性立管在波浪和海流作用下易发生立管干涉的问题,以我国南海某油田输油立管和相邻锚链为例,分别对拖曳力系数、管道单位长度质量、外径、内部介质密度、立管抗拉弯扭刚度和悬挂角度等参数进行敏感性分析,得出不同参数的敏感性情况,并在此基础上提出一些建议供实际工程设计参考.     

生石灰处理过湿粘土路基性能研究

通过对生石灰处治过湿粘土的物理性能试验分析,提出了过湿土掺灰的剂量建议值和计算公式,为生石灰处理过湿粘土在路基施工中质量控制提供参考.     

Sensitivity analysis of parameters for multi-stand roll forming using a new booting model

Multi-stand roll forming is a process that has very complicated deformation behaviour and shows significant nonlinearity.In this paper, the sensitivity analysis of parameters for multi-stand roll forming was performed via a new booting finite element method(FEM) model.Compared with the most of simulation, the new model is more consistent with production process and can account for the effects of roll rotating speed.Based on the model, the process of an open section channel formed with 10 passes was simulated and the sensitivity analysis was conducted with orthogonal experiment design combined FEM model.The multi-stand roll forming process can be efficiently analyzed by the new booting model.And sensitivity analysis shows the hardening exponent plays an important role in controlling the quality of the products.