排序方式: 共有56条查询结果,搜索用时 484 毫秒
1.
从滚镀锌生产的整个工艺过程出发,对一些重要的工序和辅助设备进行了合理的设计,提出上料自动称重、脱脂液自动循环除油、镀锌槽自动循环过滤、镀槽外溶锌、不溶性阳极、分工位自动供电、自动添加、自动生成生产报表等设计理念,并使其应用于整个生产线的设计与安装。 相似文献
2.
CFB锅炉三管严重磨损引起国内、外专家们极大地关注。较详细地论述了三管磨损的原因,并提出了解决防磨新工艺、新材料。在6台CFB锅炉防磨实践中大大延长了使用寿命,取得成功。与当今国内、外所用的防磨技术相比,本技术的工艺与材料有独特的优越性:防高温氧化、耐硬物料粒子高速冲刷磨损、合金涂层结合密实牢固、抗冲击。该技术获国家发明专利。 相似文献
3.
4.
研究了镀复条件及工艺配方对 N-P-SiC 化学复合镀层中 SiC 均匀共析的影响.结果表明,Nj-P 合金基体中 SiC 微粒子均匀共析的最佳条件是:温度87±1℃,搅拌速度600r/min·K,pH=4.8,SiC 平均粒径 D_p=3.5μm,SiC 的添加量8g/L,析出速度12~14μm/h.本文还测定了镀层的显微硬度及磨损量,并用扫描电镜观察了磨损前后的表面形貌和结构. 相似文献
5.
《铁道标准设计通讯》2017,(9):165-168
针对现代有轨电车轨道清洁的需求、国内外清洁车发展现状以及槽型轨的特殊结构,介绍一款多功能槽型轨道清洁车,简要介绍清洁车的结构组成和工作原理。建立清洁车行进速度和滚刷最小转速的数学模型,并通过虚拟样机的方法,以块状颗粒模拟污物,对3种清洁车行进速度和其相应的最小滚刷转速,进行滚刷对污物的清扫仿真实验,并分析滚刷转速和清洁车行进速度2个因子的影响。实验证明,使用该数学模型可以使滚刷转速和清洁车行进速度相匹配,当清洁车行进速度在14~30 km/h,滚刷转速n在100 r/min以上时,颗粒抛射高度较高,对槽型轨清洁效果较好。 相似文献
6.
《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2012,50(5):351-370
Nonlinear suspension controllers have the potential to achieve superior performance compared to their linear counterparts. A nonlinear controller can focus on maximizing passenger comfort when the suspension deflection is small compared to its structural limit. As the deflection limit is approached, the controller can shift focus to prevent the suspension deflection from exceeding this limit. This results in superior ride quality over the range of road surfaces, as well as reduced wear of suspension components. This paper presents a novel approach to the design of such nonlinear controllers, based on linear parameter-varying control techniques. Parameter-dependent weighting functions are used to design active suspensions that stiffen as the suspension limits are reached. The controllers use only suspension deflection as a feedback signal. The proposed framework easily extends to the more general case where all the three main performance metrics, i.e., passenger comfort, suspension travel and road holding are considered, and to the design of road adaptive suspensions. 相似文献
7.
8.
9.
介绍采用化学镀方式镀镍的原理和方法,其工艺简单、操作方便、无毒、无污染,可用来对活塞杆尾部进行防腐蚀保护。 相似文献
10.
本文介绍了获得非晶态Ni-P,SiC化学复合镀层的试验方法,研究了复合镀层在晶化条理过程中,显微硬度及磨损量的变化情况,得到了硬度高、耐磨性好的晶化处理条件,同时还研究了SiC粒径及共析量对复合镀层磨损量的影响,并对镀层的微结构进行了分析。 相似文献