Numerical study on the dynamic response of a truncated ship-hull structure under asymmetrical slamming

Dynamic response of ship-hull structure under slamming has tracked widespread attention in the marine structural design. However, our understanding on the dynamic characteristics largely relies on the symmetrical slamming cases. This paper presented a preliminary numerical investigation on the dynamic response of a truncated ship-hull structure under asymmetrical slamming based on the uncoupled CFD-FE method. Asymmetrical slamming loads were predicted through combining the seakeeping analysis and CFD method. In there, three kinds of motions (vertical, horizontal and roll motions) of 2D ship sections were obtained through the seakeeping analysis and then the slamming pressure was predicted through simulating the water entry with various motions based on CFD method. The dynamic response was analyzed through finite element method. Numerical predictions including ship motions, slamming loads and dynamic analysis were validated against published experimental data and numerical calculations. The characteristics of asymmetrical slamming loads were analyzed showing obvious asymmetry in space, and the dynamic characteristic of the ship bow structure was further clarified through discussing the deformation and stress distribution. These results are useful for readers for better understanding the dynamic characteristics of the bow structure under slamming.     

地面注汽管线表面散热损失影响因素分析

文中采用Fluent模拟与理论计算结合比较的方法,研究了不同因素对蒸汽管道散热损失的影响规律,并分析了理论计算模型的相对误差。发现增加注汽管线距地面高度,对其散热损失影响较弱;空气温度升高,注汽管道表面散热损失降低;风速和表面发射率对注汽管线表面热损失影响较大;数值模拟结果与理论计算数据相对误差较大。     

M型风电运维船船型设计与波浪增阻和耐波性能研究

本文基于三体风电运维船船型,结合M型船的特征要素设计改造出M型风电运维船。利用数值仿真技术模拟出M型风电运维船波浪航行时的波浪增阻与纵摇、垂荡情况,将数值仿真计算结果与原三体船的试验数据进行比较,以此探索不同M型船船型对船舶波浪航行时的波浪增阻与纵摇、垂荡情况的影响。最终确定了耐波性能较优的船型方案,从而为M型风电运维船船型设计提供了一定的参考和借鉴。     

基于有限元模型的船用螺旋桨桨叶应力分析

采用计算流体动力学(Computational Fluid Dynamics,CFD)软件建立静止域(舵、导管及船体)和旋转域(螺旋桨)的三维几何模型,在螺旋桨流场内求解雷诺平均纳维-斯托克斯方程(Reynolds-Averaged Navier-Stokes equations,RANS),由此对船用螺旋桨产生的推力和转矩特性进行数值模拟。对比分析在压载工况和满载工况下螺旋桨桨叶的压力分布、沿不同轴的受力情况和绕不同轴的转矩情况,为轴系弹性校中提供更加准确可靠的应力情况,对船用螺旋桨的生产设计提供有益的参考。     

4500 CDWT化学品/成品油船设计问题的实船治理

针对4 500 CDWT化学品/成品油船运营中出现船尾振动剧烈、航速低、与设计航速相差甚远等诸多问题,进行实船治理。在尽可能减少改造成本的基础上,通过修改型线设计和CFD计算分析,选定优化设计的双尾船型对该船进行改造,改造仅局限于船尾机舱段设计吃水线以下部分。该治理方案达到了预期理想的设计效果,同时也满足了最经济的治理成本,可为出现类似问题的船舶提供宝贵的实船治理经验。     

公路隧道运营通风横通道周围流场特性研究

为研究公路隧道巷道式运营通风横通道周围的流场特性,以贵州凉风坳隧道为研究背景,利用流体力学研究软件Fluent建立隧道三维模型并进行了数值仿真计算。通过在隧道两边等风速条件下,对隧道内人行横通道以及车行横通道附近的流场特点研究,分析了运营通风横通道周围流场分布的具体特点。模拟结果表明:车行横通道与人行横通道两边流场分布基本相同;横通道内风速相对较小,约为隧道内风速的10%;不同风速下,横通道附近的速度分布和总压分布整体走势一致;两边流场相对稳定,不会进行风流和污染物的串流。     

船舶舱室置换通风系统的数值模拟和优化

船上有些空间大、人员集中、船体结构复杂的舱室,传统送风方式难以满足需求,给空气环境设计带来很大挑战。文章采用计算流体力学方法研究置换通风系统在船舶舱室中的应用,通过建立物理和数值计算模型,在设计初始阶段对其进行气流组织、热舒适性等方面的模拟分析和优化应用研究;针对某实船舱室的置换通风系统原始方案和优化方案进行对比分析,结果表明置换通风系统具有流动分层和垂直温度梯度的特点。相比原始方案,优化方案使舱室内温度、风速和热舒适性指标等得到优化,有效降低了吹风感,保证人体周围的空气品质,热舒适性指标也符合标准要求。对船舶置换通风系统的应用研究具有借鉴意义。     

某平台机舱进排风口气流组织的CFD模拟

某自升式平台的机舱进、排风口位置比较接近,机舱排出的热气受大气风影响可能返回进风口,进而提高进风温度,成为一个设计隐患。文章应用CFD技术,通过模拟一定的大气环境条件下进排风口处的气流组织,找出最不利工况,并提出切实可行的改进建议。     

Validation of a dynamic mooring model coupled with a RANS solver

Standard design procedures and simulation tools for marine structures are aimed primarily for use by the offshore oil and gas. Mooring system restoring forces acting on floating offshore structures are obtained from a quasi-static mooring model alone or from a coupled analysis based on potential flow solvers that do not always consider nonlinear mooring-induced restoring forces, fluid structure interactions, and associated hydrodynamic damping effects. This paper presents the validation of a dynamic mooring system analysis technique that couples the dynamic mooring model with a Reynolds-averaged Navier-Stokes (RANS) equations solver. We coupled a dynamic mooring model with a RANS equations solver, and analyzed a moored floating buoy in calm water, regular and irregular waves and validated our motion and mooring force predictions against experimental measurements. The mooring system consisted of three catenary chains. The analyzed response comprised decaying oscillating buoy motions, linear and quadratic damping characteristics, and tensile forces in mooring lines. The generally favorable comparison of predicted buoy motions and mooring forces to experimental data confirmed the reliability of our implemented coupling technique to predict system response. Additional comparative results from a potential flow solver demonstrated the benefits of the coupled dynamic mooring model with RANS equations. The successful validated tool of coupling the dynamic mooring model with the RANS solver is available as open source, and it shows the potential of the coupled methodology to be used for analyzing the moored offshore structures.     

桨-舵间距对其组合系统水动力性能的影响

本文通过CFD方法对敞水桨、桨-舵组合以及优化间距的桨-舵组合装置开展了数值仿真研究，分析了桨-舵间距对其组合系统的水动力性能影响。螺旋桨敞水工况的计算值与物理模型试验值吻合良好，验证了数值计算方法的可行性。通过对比桨-舵间距大于推荐值的三个工况，发现在较低进阶系数下系统的节能效率有稍许增加，然而随着间距的增大，节能效率呈现降低的趋势；在高进阶系数下，随间距增大节能效率逐步降低。适当减小桨-舵间距，在较低和中等进阶系数下，随间距减小节能效率呈现逐步升高的趋势，在间距减少10mm时，组合体的节能效率最大可增加1.937%；不过在高进阶系数下，随间距减小节能效率却有下降趋势。