P2混动自动变速器的离合器自适应控制

为了解决混合动力系统动力耦合的响应性和舒适性问题，建立混动离合器C0起动发动机过程和并联动力输出模式下的功率流模型。对C0起动发动机的控制过程进行仿真分析，针对C0的起动扭矩和电机的输出扭矩在时间和空间上的匹配问题，提出以换挡离合器的滑摩控制来进行缓冲的策略。为了实现稳定精确的发动机起动控制，消除各自的扭矩控制、液压系统特性的误差，提出C0离合器起动发动机的自适应控制和B1离合器滑摩自适应控制，以换挡离合器滑差和发动机转速的超调量为监控对象，对C0离合器各阶段压力控制参数进行自适应调整，以优化发动机起动过程。研究结果表明：通过换挡离合器的滑摩控制可以很好地解决C0离合器扭矩和电机扭矩的匹配问题，即使在换挡过程中对发动机起动也能保证良好的舒适性，并控制过程时间在1.5 s内；在整车试验过程中，通过对C0压力的自适应调整，发动机转速的超调和起动冲击问题均可以得到有效解决。     

基于扭矩控制的AMT换挡控制策略研究

提出在车辆起步和换挡过程中通过CAN动力网络控制发动机的输出扭矩来改善AMT换挡品质的新方法,制定扭矩控制与离合器接合控制策略,并在装有AMT的某重型商用车上进行试验。试验结果表明,换挡过程中通过控制发动机的输出扭矩并与离合器的接合过程相协调,可显著提高AMT的换挡品质。     

并联式混合动力汽车模式切换控制策略研究

并联式混合动力汽车模式切换时离合器会介入传动系统，容易引起较明显的冲击感，是影响整车驾驶舒适性的主要因素。为此，提出了基于离合器双模糊和电机转矩协调的模式切换控制策略。首先建立混合动力汽车模式切换过程的动力学模型，以减小离合器滑磨功为目标，对模式切换时的离合器接合过程进行划分；其次，结合混合动力汽车模式切换的基本要求和驾驶意图，制定离合器双模糊控制策略，分别对滑摩阶段的接合时长和转矩同步阶段的压力变化率进行控制；然后以离合器滑磨功和整车冲击度为优化目标，采用二次型最优控制算法对滑摩阶段的接合压力进行优化，从而获取模式切换过程中离合器的最优接合压力轨迹；在此基础上，通过实时计算离合器传递转矩，根据电机转矩响应快的特点，制定电机转矩协调控制策略；最后，基于某混合动力试验样车，在底盘测功机上分别进行缓加速、中等加速和急加速下的模式切换试验，对所提出的控制策略进行验证。试验结果表明：该策略能较好地反映驾驶人驾驶意图，保证离合器的使用寿命，所产生的整车冲击度均处于合理范围之内，改善了整车模式切换过程中的驾驶舒适性。     

P2结构混合动力系统协同控制

为了提高混合动力各系统的控制效率和响应性,针对P2结构混合动力系统控制对象的特点和整车的功能需求,提出了P2结构混合动力控制系统的构架和所有有效的工作模式,并从整车运行工况和模式转换效率的角度总结了所有有效的工作模式转换真值矩阵。为了满足各节点单元的协同控制要求,提出了P2混合动力控制系统的协同控制构架,约束了各控制单元的主要功能和接口定义,并对多个控制单元之间的复合控制过程进行描述。分析了2种不同动力源在液压控制的混合动力离合器的耦合过程以及混合动力离合器与换挡离合器控制过程重叠时所带来的动力迟滞,对离合器的压力控制和发动机的启动过程时序进行了优化。在不同的控制阶段定义了关键的控制目标,建立发动机扭矩、电机扭矩、混合动力离合器控制压力三者之间的关联。结果表明：发动机、电机、变速器之间通过HCU的协同控制方法能够高效地完成混动工作模式之间的转换。整车试验验证了各系统的系统控制效果,整个模式转换过程的时间为1.5 s,换挡品质和动力响应性满足驾驶需求。     

Method for precise controlling of the at shift control system

The shift comfort and efficiency of Automatic Transmission in vehicle are highly influenced by the pressure of the clutch shift control system, especially by the electro-hydraulic clutch subsystem. In this paper, the new design principles of electro-hydraulic clutch systems developed and modeled in detail, the clutch-to-clutch control system is analyzed in three time intervals: oil filled phase, changing phase of clutch torque and synchronous phase of clutch speed. The demand pressures for the engaged clutches calculated in each phase and is precisely built up by using fuzzy slide mode control, the time of hydraulic pressure building-up is very sensitive to the dither current in simulation. All control parameters are optimized by Cosimulation between software Simulink and SimulationX. Finally, the optimal algorithm of the clutch shift control is written into the transmission control unit of a testing vehicle. The testing results show that the suggested control strategy is effective.     

混合动力传动系 Tip-in/out工况的模型预测控制

为抑制混合动力汽车加减速过程中传动系统振荡,以电机转矩为控制量,提出一种基于模型预测主动控制混合动力传动系统振荡的策略,基于 Matlab/Simulink平台搭建动态系统模型,实时计算电机转矩补偿优化发动机输出转矩,准确跟踪目标转矩的同时减少传动系统振荡。探索不同控制器参数设置对于驾驶动力性和舒适性的增益效果,通过硬件在环 （Hardware-in-Loop,HIL） 试验表明,所设计的 MPC控制器能使汽车平稳地加减速,迅速跟踪目标转速,求解时间控制在10 ms以内,具有较好的实时性,同时对传动系统中的非线性因素和参数变化有较好的鲁棒性。     

新型混合动力汽车动力切换动态过程分析

为对基于行星齿轮机构的新型混合动力系统由纯电动驱动切换至发动机驱动过程中的转矩波动进行研究,建立了新型混合动力传动系统的动力学模型,对动力切换过程进行了分析.提出了该过程的转矩协调控制策略,并通过仿真和台架试验进行了验证.结果表明,该转矩协调控制策略能有效减小纯电动驱动切换至发动机驱动过程中的转矩波动和对整车的冲击.     

Development and implementation of a torque vectoring algorithm for an innovative 4WD driveline for a high-performance vehicle

The sporting spirit that characterises a high-performance car can be observed in certain technical solutions. The power distribution on the rear wheels is the simplest example of that. It is well known that rear-wheel drive (RWD) vehicles are more fun to drive and faster in their reactions. Unfortunately, they are also less intuitive and harder to control because of their natural oversteering behaviour. The idea of maintaining an RWD driveline in the future is not farseeing, because it would imply an excessive tyre dimension increasing to let the driver use all engine power in many cornering and low-friction conditions. The choice of adopting a part-time all-wheel drive (AWD) driveline comes from the will of enhancing the overall performance by using all the available friction every time that it is needed. It has to be kept into account that a normally aspirated motor of a sport car can supply 500–600 Hp nowadays, and that it will supply 700–800 Hp in the very near future. However, the proposed driveline has not to worsen the weight characteristics (mass and load distribution) that make an RWD vehicle better than other cars. Because of all these considerations and constraints, a new driveline system has been designed. It derives from an RWD driveline with a semi-active differential, to which has been added a controlled wet clutch that directly connects the engine to the front differential. This device allows the drive torque to be distributed between the two axles. It can be understood that in such a device, the torque distribution does not depend only on the central clutch action, but also on the engaged gear. Because of this particular layout, this system can not work in the whole gear range because of thermal problems due to kinematical reasons. So the centre clutch controller has to consider the gear position too. The control algorithms development was carried out using a vehicle model, which can precisely simulate the handling response, the powertrain dynamic, and the actuation system behaviour. Such a modelling precision required the development of a customised powertrain model library in Matlab/Simulink.     

Improved optimal controller for start-up of amt trucks in consideration of driver’s intention

A linear-quadratic optimal controller is proposed for vehicle start-up, which is designed as a linear feedback form of the states and the measured (estimated) disturbances. The requirements of less friction loss and less driveline shock are represented by the weighting matrices of the cost function. The driver’s intension is also considered and the controller gains are adjusted on-line accordingly. The designed control strategy is tested on a complete powertrain simulation model. Through large amount of simulations, it is verified that the system is robust to the variations of driving conditions, such as variation of vehicle mass and road grade. It is also shown that the control performance is influenced greatly by the estimation error of engine torque and clutch torque, and the acceptable level of mean estimation error is about ±10%.     

大功率自动变速器换挡离合器调压控制研究

为了改善大功率自动变速器换挡过程中换挡离合器（含湿式制动器和湿式离合器）油压的调控水平,提高车辆的换挡品质,从结构上在换挡离合器中设计平衡活塞来补偿离合器旋转离心的影响,并在排油回路中增加背压阀以消除活塞腔内空气造成的不确定性。通过对换挡执行系统结构进行分析,分别针对离合器活塞、电液调压过程及离合器滑摩过程进行模型计算,在此基础上,将惯性相的充油调压控制进行拆解,即在转矩相结束时刻初始常量的基础上叠加一阶控制过程,针对换挡过程中系统存在非线性干扰和参数不确定性的特点,结合系统特性的分阶段试验标定,制定了换挡离合器调压过程的滑模控制策略,并基于MATLAB环境对控制策略的正确性和有效性进行仿真分析,最后进行实车试验验证。研究结果表明：无论是制动器充油还是旋转离合器充油,控制策略均能将惯性相持续时间、换挡冲击和滑摩功率损失等控制在合理范围;控制策略具有良好的性能,旋转离合器和制动器都能实现稳健的惯性相调压控制。     

Shifting control of an automated mechanical transmission without using the clutch

The automated mechanical transmission (AMT) is gaining popularity in the automotive industry, due to its combination of the advantages of mechanical transmissions (MT) and automatic transmissions (AT) in terms of fuel consumption, low cost, improved driving comfort and shifting quality. However, the inherent structural characteristics of the AMT lead to disadvantages, including excessive wear of the clutch plates and jerk and traction interruption during the shift process, that severely affect its popularity in the automatic transmission industry. The emerging technology of shifting control without the use of the clutch is a promising way to improve the shifting transients of AMTs. This paper proposes a control algorithm that combines speed and torque control of the AMT vehicle powertrain to achieve shifting control without using the clutch. The key technologies of accurate engine torque and speed control and rapid position control of the shift actuators are described in detail. To realize accurate engine speed control, a combined control algorithm based on feed-forward, bang-bang and PID control is adopted. Additionally, an optimized closed-loop position control algorithm based on LQR is proposed for the shift actuators. The coordinated control algorithm based on engine and shift actuator control is described in detail and validated on a test vehicle equipped with an AMT. The results show that the coordinated control algorithm can achieve shifting control without the use of the clutch to improve driving comfort significantly, reduce shift transients and extend the service life of the clutch.     

Lateral stability control of dynamic steering for dual motor drive high speed tracked vehicle

In this paper, the torque and power required by dual motors for electric tracked vehicle during dynamic steering maneuvers with different steering radiuses are analyzed. A steering coupling drive system composed of a new type of center steering motor, two Electromagnetic (EM) clutches, two planetary gear couplers, and two propulsion motors is proposed for the dual motors drive high speed electric tracked vehicle (2MHETV), which aims to improve its lateral stability. An average torque direct distribution control strategy based on steering coupling and an optimization-distribution-based close-loop control strategy are designed separately to control the driving torque or regenerative braking torque of two propulsion motors for vehicle stability enhancement. Then models of the 2MHETV and the proposed control strategy are established in Recudyn and Matlab/Simulink respectively to evaluate the lateral stability of dynamic steering for the 2MHETV with different steering radiuses on hard pavement.The simulation results show that the lateral stability of the 2MHETV can be significantly improved by the proposed optimization-distribution-based close-loop control strategy based on steering coupling system.     

基于补偿滑模控制的混合动力汽车协调控制

由于行星排功率分流式混合动力汽车的结构优势,双行星排功率分流式混合动力汽车已经成为各机构的研究重点。由纯电动模式到混合驱动模式切换的过程中存在发动机起动和发动机转矩引入,而发动机转矩瞬态响应存在迟滞,导致切换过程中动力系统的输出转矩会有较大波动。为减小波动,降低模式切换过程中的动态冲击度,本文中提出补偿滑模控制方法,对双行星排功率分流式混合动力汽车模式切换进行协调控制。首先,建立整车动力学模型,对切换过程每个模式进行分析;之后,针对发动机拖转阶段和混合驱动阶段分别采用补偿控制和基于固定边界层的自适应滑模控制,并对滑模控制进行稳定性分析;最后,结合Matlab/Simulink软件平台进行仿真验证。仿真结果表明,补偿滑模协调控制策略能够有效地减小从纯电动到混合驱动模式切换过程中的转矩波动和冲击度。     

基于扩展状态观测器和滑模控制的双离合器自动变速器起步自适应控制

双离合器自动变速器（Dual Clutch Transmission,DCT）随着服役时间的增加离合器性态会发生变化导致起步性能下降,为降低离合器性态变化对起步性能的影响,提出一种基于扩展状态观测器和滑模控制的DCT起步自适应控制方法。首先,建立DCT起步动力学模型、发动机模型和液压控制系统模型;将DCT起步问题转化为参考轨迹跟踪问题,通过工况识别并利用极小值原理获得了不同起步工况的参考轨迹;在DCT起步动力学模型中将与离合器性态变化相关的项定义为不确定项,设计扩展状态观测器对不确定项进行估计,同时结合自适应滑模控制器,获得了起步发动机转矩和离合器油压的自适应控制率;为了跟踪发动机转矩和离合器油压的自适应控制率,设计了发动机转矩跟踪控制器,同时对液压系统采用了PID闭环控制;通过MATLAB/Simulink平台仿真以及台架试验验证所提出的DCT起步控制方法对离合器性态变化的自适应效果。研究结果表明：所提出的起步自适应控制方法能够有效避免由离合器性态变化导致的起步延时,同时1挡缓起步和急起步的仿真冲击分别减小了53.11%和43.42%,试验起步冲击分别减小了35.66%和30.31%。     

基于小波控制的电动汽车稳定性研究（双语出版）

针对前轮独立驱动电动汽车,研究一种基于小波控制器的驱动稳定性控制系统。为提高车辆对开路面的行驶稳定性,根据驱动轮等转矩分配控制策略,提出基于神经网络PID的驱动轮滑移率相近为目标控制策略。针对矢量控制中的电流控制,提出基于离散小波变换的电流控制器。通过CarSim/Simulink建立前轮独立驱动电动汽车联合仿真平台,进行不同工况整车性能仿真与分析,并基于A&D5435快速原型开发平台进行实车试验。仿真与试验结果表明：基于小波控制器的驱动控制系统不仅提高了车辆对开路面行驶的稳定性,而且具有更平滑、更快速的转矩响应;对开路面工况下,提出的控制策略左侧、右侧驱动轮速度仿真结果与试验结果最大偏差分别为3.43%和3.56%;等转矩分配控制策略下,左侧、右侧驱动轮速度仿真结果与试验结果最大偏差分别为3.86%和3.25%,表明了试验与仿真的一致性;对开路面仿真工况下,相比于驱动轮等转矩分配控制策略,基于神经网络PID的驱动轮滑移率相近为目标控制策略的车辆峰值质心侧偏角降低了79.57%,侧向跑偏距离降低了73.39%。     

Optimal torque coordinating control of the launching with twin clutches simultaneously involved for dry dual-clutch transmission

As for the self-developed six-speed dry dual-clutch transmission (DCT), the optimal torque-coordinated control strategy between engine and dual clutches is proposed to resolve the problem of launching with twin clutches simultaneously involved based on the minimum value principle. Focusing on the sliding friction phase of the launching process, dynamics equations of dry DCT with two intermediate shafts are firstly established, and then the optimal transmitting torque variation rate and the driven plate's rotating speed of dual clutches are deduced by using the minimum value principle, in which the jerk intensity and friction work are taken as the performance indexes, and the terminal constraints of state variables are determined according to the driver's launching intention. Besides, the separating conditions of non-target gear clutch and the torque distributing relations of twin clutches are derived from the launching control targets that guarantee the approximately equal friction extent of two clutches and no power cycle. After the synchronisation of driving and driven plates of on-coming clutch, the output torque of engine is smoothly switched to the driver's demand level. Furthermore, launching the simulation model of the dry DCT vehicle is set up on the Matlab/Simulink platform. Simulation results indicate that the proposed launching control strategy not only can effectively reflect the driver's intention and extend the life span of twin clutches, but also obtain an excellent launching quality. Finally, the torque control laws of two clutches obtained through the simulation are transformed into clutch position control laws for the future realisation in the real car, and the closed-loop position controls of twin clutches in the launching process are conducted on the test bench with two sets of clutch actuator, obtaining preferable tracking effects.     

手动挡汽车换挡困难原因及改进方法

汽车换挡困难影响汽车性能的发挥和正常驾驶。文章从离合、离合操纵、变速器及变速操纵4个方面分析了换挡困难的影响因素,并针对各个影响因素提出改进方法,提出了可行的评价换挡操控性优劣的方法。在设计过程中,以上4个方面是逐一排查换挡困难的关键要素,并通过反复的主观评价和逐步优化,可以取得良好的效果。     

具有双离合器的液力变矩器的结构设计

将液力变矩器与机械式自动变速器合理匹配可组成一种新型自动变速系统，其性能接近自动变速器，但成本降低。为该系统设计了具有双离合器(闭锁离合器，换档离合器)的液力变矩器。阐述了该液力变矩器的结构、工作原理及特点。试验结果表明，所设计液力变矩器可支持新型自动变速系统成为现实。     

Wet Single Clutch Engagement Behaviors in the Dual-Clutch Transmission System

A frictional torque was generated by a lubricated slip contact between a wet clutch pad and a steel separator during a wet clutch engagement. It is necessary to understand the generation of frictional torque to improve the performance of the frictional torque transfer and the durability of the wet clutch system. The analytical modeling of wet clutch torque transfer considers the effects of surface roughness, permeability, the elastic modulus of the frictional material, lubricant viscosity, temperature, etc. Experimental apparatus for wet clutch engagement was designed for the measurement of frictional torque transfer during wet clutch engagement. The experimental results were compared with the analytical results under various operational conditions for the verification of the theoretical analysis to evaluate the performance of the wet clutch system. Some correlations were investigated between the experimental and analytical results. We found that computation by analytical modeling can predict the effects of oil temperature, applied force, and slip speed, as well as engagement period and frictional torque transfer shapes.     

机械式自动变速器起车过程综合控制

分析机械式自动变速器在各种工况下起车离合器接合过程，以起车冲击度和滑摩功均较小为原则，来实现离合器结合的平顺性。根据油门开度、发动机转速、输入轴转速计算发动机的负荷能力，控制离合器传递的扭矩使发动机输出扭矩与离合器扭矩匹配。另外建立滑摩功与离合器温升的模型，防止离合器摩镣片过温损坏。据此建立起车离合器控制MAP图，已应用于某车型的AMT样车上。