电动汽车再生制动的滑移率控制

以不改变电动汽车原有机械制动系统结构和控制方式为前提,提出一种并联式混合制动滑移率控制方法.该方法明确划分了再生制动控制和原有机械制动控制的作用工况.将再生制动控制转化为滑移率规划和控制两个问题,并设计了滑模控制器.分析和仿真结果显示,在不同强度、不同方式及存在参数不确定性下制动,该方法都可以实现再生制动和机械制动的准确控制及平顺过渡.     

车轮防抱死制动滑移模式控制律的理论研究

本文通过建立轮制动时的力学模型，运用现代控制理论中的滑移模式控制方法，对汽车防抱死制动控制律进行了理论分析与研究。     

汽车防抱死制动系统的自抗扰控制研究

汽车防抱死制动系统（Anti-lock Braking System,ABS）的作用是确保汽车制动时行驶方向的稳定性、可靠性,但是目前仍存在非线性、时变性以及参数不确定性等问题。为保证汽车制动行驶过程中的操纵稳定性和安全性,进一步实现各工况下防抱死制动系统的优化控制,以影响整车稳定的变量滑移率为研究对象,分析所设计策略的控制效果。搭建汽车动力学模型、制动系统模型、轮胎模型和滑移率模型等主要模型,设计基于滑移率的ABS二阶非线性自抗扰控制器。运用MATLAB/Simulink软件对基于自抗扰控制（Active Disturbance Rejection Control,ADRC）的ABS制动过程和基于模糊PID控制的ABS制动过程进行仿真,对比研究最佳滑移率、载荷、水泥-冰对接路面、扰动等对制动过程中的轮速、车速以及滑移率等动态性征反映的稳定性和抗扰能力的影响,同时研究其对最终制动距离和最终制动时间反映的制动性能的影响。最后,将自抗扰控制器和模糊PID控制器装配于试验车辆的ABS,进行水泥路面和冰-水泥对接路面制动过程的实车试验。研究结果表明：基于二阶非线性自抗扰控制算法的ABS制动的最终制动距离和最终制动时间更短、制动效果更优,制动过程中的轮速、车速和滑移率在响应速度、稳定性和抗扰能力等方面均更佳;试验结果与仿真结果吻合,证明了仿真模型及其仿真结果的可行性和正确性。     

滑模变结构汽车ABS滑移率控制方法的研究

提出了一种用于ABS滑移率控制的滑模变结构控制方法,通过将实际滑移率与参考滑移率作比较,形成滑动面,追踪参考滑移率来使ABS系统处于制动的最佳区域。并且采用了饱和函数来削弱变结构带来的颤抖现象,经仿真表明,该方法在ABS的滑移率控制中是切实有效的。     

Transient switching control strategy from regenerative braking to anti-lock braking with a semi-brake-by-wire system

Regenerative braking is an important technology in improving fuel economy of an electric vehicle (EV). However, additional motor braking will change the dynamic characteristics of the vehicle, leading to braking instability, especially when the anti-lock braking system (ABS) is triggered. In this paper, a novel semi-brake-by-wire system, without the use of a pedal simulator and fail-safe device, is proposed. In order to compensate for the hysteretic characteristics of the designed brake system while ensure braking reliability and fuel economy when the ABS is triggered, a novel switching compensation control strategy using sliding mode control is brought forward. The proposed strategy converts the complex coupling braking process into independent control of hydraulic braking and regenerative braking, through which a balance between braking performance, braking reliability, braking safety and fuel economy is achieved. Simulation results show that the proposed strategy is effective and adaptable in different road conditions while the large wheel slip rate is triggered during a regenerative braking course. The research provides a new possibility of low-cost equipment and better control performance for the regenerative braking in the EV and the hybrid EV.     

低附着弯道路面车辆制动力控制策略研究

分析了车辆ABS系统在弯道制动时存在的横向稳定性问题,提出了一种低附着弯道路面车辆制动力控制策略.它综合考虑车轮防抱死与车辆发生侧滑时所能承受的最大侧向力,根据两者所允许的最大制动力中较小值确定施加于车辆的制动力.所进行的数值仿真结果表明该控制方法能提高车辆在低附着弯道路面上的横向稳定性.     

Wheel slip control with torque blending using linear and nonlinear model predictive control

Modern hybrid electric vehicles employ electric braking to recuperate energy during deceleration. However, currently anti-lock braking system (ABS) functionality is delivered solely by friction brakes. Hence regenerative braking is typically deactivated at a low deceleration threshold in case high slip develops at the wheels and ABS activation is required. If blending of friction and electric braking can be achieved during ABS events, there would be no need to impose conservative thresholds for deactivation of regenerative braking and the recuperation capacity of the vehicle would increase significantly. In addition, electric actuators are typically significantly faster responding and would deliver better control of wheel slip than friction brakes. In this work we present a control strategy for ABS on a fully electric vehicle with each wheel independently driven by an electric machine and friction brake independently applied at each wheel. In particular we develop linear and nonlinear model predictive control strategies for optimal performance and enforcement of critical control and state constraints. The capability for real-time implementation of these controllers is assessed and their performance is validated in high fidelity simulation.     

轮胎附着极限下差动制动对汽车横摆力矩的影响

本文以纵滑－侧偏联合工况的稳态轮胎模型为基础，分析了汽车极限转向条件下制动作用于不同车轮时对汽车横摆力矩的影响，并通过整车动力学仿真进行了验证，研究结果为利用差动制动控制提高汽车的高速操纵稳定性提供了动力学依据。     

Slip regulation for anti-lock braking systems using multiple surface sliding controller combined with inertial delay control

In this paper, a multiple surface sliding controller is designed for an anti-lock braking system to maintain the slip ratio at a desired level. Various types of uncertainties coming from unknown road surface conditions, the variations in normal force and the mass of the vehicle are estimated using an uncertainty estimation technique called the inertial delay control and then the estimate is used in the design of the multiple surface sliding controller. The proposed scheme does not require the bounds of uncertainties. The ultimate boundedness of the overall system is proved. The proposed scheme is validated by simulation under various scenarios of road friction, road gradient and vehicle loading followed by experimentation on a laboratory anti-lock braking set-up for different friction conditions.     

Longitudinal wheel slip during ABS braking

Anti-lock braking system (ABS) braking tests with two subcompact passenger cars were performed on dry and wet asphalt, as well as on snow and ice surfaces. The operating conditions of the tyres in terms of wheel slip were evaluated using histograms of the wheel slip data. The results showed different average slip levels for different road surfaces. It was also found that changes in the tyre tread stiffness affected the slip operating range through a modification of the slip value at which the maximum longitudinal force is achieved. Variation of the tyre footprint length through modifications in the inflation pressure affected the slip operating range as well. Differences in the slip distribution between vehicles with different brake controllers were also observed. The changes in slip operating range in turn modified the relative local sliding speeds between the tyre and the road. The results highlight the importance of the ABS controller's ability to adapt to changing slip–force characteristics of tyres and provide estimates of the magnitude of the effects of different tyre and road operating conditions.     

基于视觉识别的线控制动压力滑模控制

制动安全是车辆主动安全的关键技术之一。制动决策和执行器控制是影响线控制动系统性能的两个主要因素。路面自适应性和控制器鲁棒性分别对制动决策和执行器控制有着重要影响,制约着线控制动系统的发展。本文中以一种液压调控的线控制动系统为基础,针对路面自适应性和控制器鲁棒性问题,提出一种双层结构的制动系统控制器,上层采用计算机视觉的方法对路面类型进行识别,根据识别结果制定当前路面的最佳滑移率;下层针对制动系统参数不确定性问题,引入滑模控制理论对制动过程中的最佳滑移率进行跟踪控制。通过仿真与实验验证,结果表明,双层结构的制动系统控制器相比传统控制器,路面的自适应性好,制动距离更短,控制器鲁棒性好。     

防抱制动系统控制算法的仿真研究

本文用要平面法分析了目前汽车上广泛使用的Ｐ１Ｒ３逻辑控制算法在不同条件下的收敛性，因这种算法只能使车轮的滑移率在μ－Ｓ曲线的峰值点变化，故采用逻辑控制的ＡＢＳ系统不能充分发挥它的最佳效能，本文进一步通过仿真研究了基于滑移率Ｓ的控制算法，并根据逻辑控制和滑移率控制的缺陷，提出了基于路面附着系数μ的控制算法，在理想状态下的证实了所提算法的有效性。     

Development of a new traction control system for vehicles with automatic transmissions

A traction control system (TCS) is used to improve the acceleration performance on slippery roads by preventing excessive wheel slip. In this paper, a new traction control system using the integrated control of gear shifting and throttle actuation is developed for vehicles with automatic transmissions. In the design of the slip controller, by means of a differential manifold transformation, a slip control system with nonlinearities and uncertainties is transformed into a linear system, and a sliding mode controller is applied for the purpose of increasing the robustness of the system. Next, to achieve the required driving torque, the optimal throttle and gear position, maps are constructed based on dynamic programming. The simulation results indicate that the present traction control system can improve the acceleration performance of an automatic transmission vehicle for various types of road conditions.     

基于Matlab的ABS不同控制方式的仿真

汽车防抱制动系统（ABS）能实时控制车辆产生最佳的制动力矩,避免产生过大的车轮滑移,从而保持汽车的操纵性和稳定性。文中分别采用PID控制、逻辑开关控制两种方法对单轮汽车模型进行了模拟仿真。然后与没有ABS的情况进行对比,通过对仿真图形曲线的分析,得出ABS的防抱死效果明显。     

基于路面附着系数曲线的最佳滑移率计算方法

滑模控制应用于ABS系统中可较好地跟踪任意指定滑移率,但最佳滑移率却随着路面情况而变化。从单轮制动时动力学模型着手,提出了基于附着系数曲线求取最佳滑移率的防抱死制动方法,间接实现了滑模控制器对最佳滑移率的跟踪控制,并通过计算机仿真,验证了此方法的可行性和有效性。     

An investigation of the effects of pneumatic actuator design on slip control for heavy vehicles

Progress in reducing actuator delays in pneumatic brake systems is opening the door for advanced anti-lock braking algorithms to be used on heavy goods vehicles. However, little has been published on slip controllers for air-braked heavy vehicles, or the effects of slow pneumatic actuation on their design and performance. This paper introduces a sliding mode slip controller for air-braked heavy vehicles. The effects of pneumatic actuator delays and flow rates on stopping performance and air (energy) consumption are presented through vehicle simulations. Finally, the simulations are validated with experiments using a hardware-in-the-loop rig. It is shown that for each wheel, pneumatic valves with delays smaller than 3 ms and orifice diameters around 8 mm provide the best performance.     

汽车制动性能分析和计算机模拟与试验验证

本文提出了一种汽车直接线制动性能的分析和计算方法，并对具体的车型进行了模拟计算和实车道路试验，分析结果表明，计算与试验具有较好的一致性，相比之下，在计算中引入滑移率，考虑车轮半径变化等因素，所得结果更为接近实车路试结果，用所述的分析和计算方法分析汽车制动性能，揭示出用传统方法分析时所掩盖了的一些重要现象，且为在汽车制动性能分析中综合考虑人机工程的因素提供了一种途径。     

633X微型车制动稳定性理论分析

针对某厂生产的633X微型车制动侧滑稳定性问题，从整车与制动器的匹配上进行理论计算分析。计算分析结果表明，该车型整车质心纵向分配极不合理，同步附着系数偏小，制动临界减速度低，制动效能不高，而前后制动器给出的制动力分配比又不能满足整车高制动力分配比的要求，从而导致制动时后轮先抱死出现严重的侧滑甩尾现象。     

Non-singular slip (NSS) method for longitudinal tire force calculations in a sudden braking simulation

In a dynamic vehicle simulation, longitudinal tire force is primarily based on the longitudinal slip (ratio). In the longitudinal slip formula, state variables are used in the denominator. This causes a divergence problem for numerical simulations of vehicle dynamics. To avoid this numerical singularity, a differential slip calculation method was developed for use in dynamic vehicle simulations. However, this method also causes a singularity when the wheel velocity approaches zero in a pure slip state, such as during sudden braking. In this paper, a new longitudinal slip calculation method, which can overcome singularities in all velocity conditions, is proposed. For this purpose, the Taylor series is adapted to the slip formula and the idea of virtual wheel rotation stiffness is introduced for the development of the slip equation. The physical phenomenon at the zero slip state is analyzed. Finally, the proposed slip formula is used to solve the numerical singularity problem, and the non-singular slip (NSS) calculation method is proposed. The proposed NSS method is applied to tire model performance test (TMPT) simulations to validate its performance.     

Coordinated vehicle traction control based on engine torque and brake pressure under complicated road conditions

Vehicle traction control system has been developed to enhance the traction capability and the direction stability of the driving wheels through the tyre slip ratio regulation. Under normal situations, if the tyre slip ratio exceeds a certain threshold, the slip ratio of the driving wheel is regulated by the coupled interaction of the engine torque and the active brake pressure. In order to obtain the best driving performance on a road under complicated friction conditions, the driving torque and the active brake pressure, need to be decoupled and adjusted to avoid penalisation of each other. In this paper, a coordinated cascade control method with two sliding-mode variable structure controllers is presented. In this control method, the driving wheel slip ratio is regulated by adjusting the engine torque and the wheel brake pressure. Through the sliding-mode controller, the engine torque is tuned to achieve the maximum driving acceleration and then the active brake pressure is applied to the slipped wheel for further modification of the wheel slip ratio. The advantage of this control method is that through proper regulation, the conflict between the two control inputs could be avoided. Finally, the simulation results validate the effectiveness of the proposed method.