Characteristics of truck traffic in Singapore

This paper presents the results of a project conducted to study the characteristics of truck traffic in Singapore. Detailed traffic surveys recording counts of vehicles by axle-configuration were performed at 219 sites over a period of nearly two years. The surveys covered 5 different road classes, namely expressways, arterials, collectors, industrial roads and local roads. It was found that the time distribution of truck travel were not the same among the five road classes. The peaking characteristics of truck traffic were less pronounced compared to passenger car traffic. The peak hour truck volume varied from 67.0% to 9.7% of the daily truck traffic as compared to 13.8% for passenger car traffic. The lane distribution pattern of truck traffic was studied in detail by road class, and was found to be a function of total directional traffic volume, total directional truck volume and the number of traffic lanes. Composition analysis was also carried out to study the lane use characteristics of single- and multiple-unit trucks.     

Impact of heavy vehicles on surrounding traffic characteristics

This work examines the impact of heavy vehicle movements on measured traffic characteristics in detail. Although the number of heavy vehicles within the traffic stream is only a small percentage, their impact is prominent. Heavy vehicles impose physical and psychological effects on surrounding traffic flow because of their length and size (physical) and acceleration/deceleration (operational) characteristics. The objective of this work is to investigate the differences in traffic characteristics in the vicinity of heavy vehicles and passenger cars. The analysis focuses on heavy traffic conditions (level of service E) using a trajectory data of highway I‐80 in California. The results show that larger front and rear space gaps exist for heavy vehicles compared with passenger cars. This may be because of the limitations in manoeuvrability of heavy vehicles and the safety concerns of the rear vehicle drivers, respectively. In addition, heavy vehicle drivers mainly keep a constant speed and do not change their speed frequently. This work also examines the impact of heavy vehicles on their surrounding traffic in terms of average travel time and number of lane changing manoeuvres using Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Networks (AIMSUN) microscopic traffic simulation package. According to the results, the average travel time increases when proportion of heavy vehicles rises in each lane. To reflect the impact of heavy vehicles on average travel time, a term related to heavy vehicle percentage is introduced into two different travel time equations, Bureau of Public Roads and Akçelik's travel time equations. The results show that using an exclusive term for heavy vehicles can better estimate the travel times for more than 10%. Finally, number of passenger car lane changing manoeuvres per lane will be more frequent when more heavy vehicles exist in that lane. The influence of heavy vehicles on the number of passenger car lane changing is intensified in higher traffic densities and higher percentage of heavy vehicles. Large numbers of lane changing manoeuvres can increase the number of traffic accidents and potentially reduce traffic safety. The results show an increase of 5% in the likelihood of accidents, when percentage of heavy vehicles increases to 30% of total traffic. Copyright © 2014 John Wiley & Sons, Ltd.     

Developing passenger car equivalents for heavy vehicles on freeways during queue discharge flow

This paper investigates the hypothesis that the effect of heavy vehicles on traffic is greater during congestion than during undersaturated conditions. A new approach was developed to quantify this effect by deriving passenger car equivalents (PCEs) using queue discharge flow (QDF) capacity as the equivalency criterion. This approach is based on the premise that QDF capacity observations can be expected to show minimal variation if traffic stream was uniform and consisted of passenger cars only. Two sites in Ontario, Canada were used for this research. The first is located at an entrance ramp merge area and the second at a long-term freeway reconstruction zone. Nonlinear programming was utilized to perform optimizations on a number of data sets at each site. Results strongly suggest that the research hypothesis is true and that the approach developed by this research is both plausible and feasible. The mean PCE factor at the first site was 2.36 versus 1.5 in the Highway Capacity Manual (HCM) 2000. At the second site, the mean PCE factors in the two directions of travel were 3.21 and 2.7 versus 2.0 in the HCM 2000. Results also showed that the PCE factor developed from the optimization runs behaves as a random variable that generally follows the normal distribution. Furthermore, the PCE factor was neither a function of weather conditions nor of roadside maintenance work.     

Modelling heavy vehicle car‐following behaviour in congested traffic conditions

This study develops a car‐following model in which heavy vehicle behaviour is predicted separately from passenger car. Heavy vehicles have different characteristics and manoeuvrability compared with passenger cars. These differences could create problems in freeway operations and safety under congested traffic conditions (level of service E and F) particularly when there is high proportion of heavy vehicles. With increasing numbers of heavy vehicles in the traffic stream, model estimates of the traffic flow could be degrades because existing car‐following models do not differentiate between these vehicles and passenger cars. This study highlighted some of the differences in car‐following behaviour of heavy vehicle and passenger drivers and developed a model considering heavy vehicles. In this model, the local linear model tree approach was used to incorporate human perceptual imperfections into a car‐following model. Three different real world data sets from a stretch of freeway in USA were used in this study. Two of them were used for the training and testing of the model, and one of them was used for evaluation purpose. The performance of the model was compared with a number of existing car‐following models. The results showed that the model, which considers the heavy vehicle type, could predict car‐following behaviour of drivers better than the existing models. Copyright © 2013 John Wiley & Sons, Ltd.     

Heavy commercial vehicles‐following behavior and interactions with different vehicle classes

This work investigates the effect of heavy commercial vehicles on the capacity and overall performance of congested freeway sections. Furthermore, the following behaviors of heavy commercial vehicles and its comparison with passenger cars are presented. Freeways are designed to facilitate the flow of traffic including passenger cars and trucks. The impact of these different vehicle types is not uniform, creating problems in freeway operations and safety particularly under heavy demand with a high proportion of heavy vehicles. There have been very few studies concerned with the traffic behavior and characteristics of heavy vehicles in these situations. This study draws on extensive data collected over a long stretch of freeway using videotaping and surveys at several sites. The collected data were firstly used to study the interaction between heavy vehicles and passenger cars. Through a detailed trajectory analysis, the following behaviors of 120 heavy vehicles were then analyzed to provide a thorough understanding of heavy vehicles‐following behavior mechanism. The results showed a significant difference in the following behavior of heavy vehicles compared with other vehicles. Copyright © 2011 John Wiley & Sons, Ltd.     

Optimal tolls for multi-class traffic: Analytical formulations and policy implications

This paper puts together an analytical formulation to compute optimal tolls for multi-class traffic. The formulation is comprised of two major modules. The first one is an optimization component aimed at computing optimal tolls assuming a Stackelberg game in which the toll agency sets the tolls, and the equilibrating traffic plays the role of the followers. The optimization component is supported by a set of cost models that estimate the externalities as a function of a multivariate vector of traffic flows. These models were estimated using Taylor series expansions of the output obtained from traffic simulations of a hypothetical test case. Of importance to the paper is the total travel time function estimated using this approach that expresses total travel time as a multivariate function of the traffic volumes. The formulation presented in the paper is then applied to a variety of scenarios to gain insight into the optimality of current toll policies. The optimal tolls are computed for two different cases: independent tolls, and tolls proportional to passenger car equivalencies (PCE).The numerical results clearly show that setting tolls proportional to PCEs leads to lower values of welfare that are on average 15% lower than when using independent tolls, though, in some cases the total welfare could be up to 33% lower. This is a consequence of two factors. First, the case of independent tolls has more degrees of freedom than the case of tolls proportional to PCEs. Second, tolls proportional to PCEs do not account for externalities other than congestion, which is likely to lead to lower welfare values.The analytical formulations and numerical results indicate that, because the total travel time is a non-linear function of the traffic volumes, the marginal social costs and thus the optimal congestion tolls also depend on the traffic volumes for each vehicle class. As a result of this, for the relatively low volumes of truck traffic observed in real life, the optimal congestion tolls for trucks could indeed be either lower or about the same as for passenger cars. This stand in sharp contrast with what is implied in the use of PCEs, i.e., that the contribution to congestion are constant. This latter assumption leads to optimal truck congestion tolls that are always proportional to the PCE values.The comparison of the toll ratios (truck tolls divided by passenger car tolls) for both observed and optimal conditions suggests that the tolls for small trucks are about the right level, maybe a slightly lower than optimal. However, the analysis of the toll ratio for large trucks seems to indicate a significant overcharge. The estimates show that the average observed toll ratio for large trucks is even higher than the maximum optimal toll ratio found in the numerical experiments. This suggests that the tolls for large trucks are set on the basis of revenue generation principles while the passenger car tolls are being set based on a mild form of welfare maximization. This leads to a suboptimal cross-subsidization of passenger car traffic in detriment of an important sector of the economy.     

货车自动驾驶技术及标准法规发展分析

目前,自动驾驶技术在乘用车领域已获得突破性发展;为提高通行效率和出行安全起到了极大的作用。自动驾驶技术在商用车领域的应用,有望较好解决高昂的人力成本和难以提高的效率等问题。然而,目前自动驾驶技术在货车的应用大多采用跟乘用车同样的标准进行规范,这在实际应用中存在着诸多的问题;例如,在FCW和AEB功能中货车在相同车速的制动距离要远大于乘用车,而其所采用标准规定的碰撞预警时间却并无多大不同,这在实际场景中存在着较大的安全隐患[1,2]。此外,货车质量和体积较大,且较多应用于长途运输,运输过程中会经历包括高温、严寒、山区等多种复杂气候场景,这些都将对货车自动驾驶技术在车辆制动效能、能耗以及多场景应用等方面提出更有针对性规范的要求。本文针对货车的应用场景特点,为其自动驾驶技术应用标准化提出了建议。     

Lane-harmonised passenger car equivalents for heterogeneous expressway traffic

In order to account for variations in traffic composition during traffic analysis, passenger car equivalent (PCE) factors are used to convert flow rates of various vehicle classes into flow rates in terms of passenger car units (PCUs). Earlier studies have developed various methods to estimate PCE values but only a few of them are based on uninterrupted traffic flow, particularly for flow regimes with heterogeneous traffic where differential (lower) speed limits are imposed on commercial vehicles. This paper proposes a lane-harmonisation approach, which leverages on the high variation in traffic composition across the lanes, to estimate PCE factors for urban expressways. Multiple linear regression is used and the PCE factors obtained for motorcycles, light goods vehicles, and heavy goods vehicles are 0.65, 1.53, and 2.75, respectively. The estimated capacity flow rate after the application of the obtained PCE factors is around 2200 PCUs per hour per lane.     

Improving estimates of transportation emissions: Modeling hourly truck traffic using period-based car volume data

We estimate hourly truck traffic using period-based car volumes that are usually available from travel demand models. Due to the lack of local or regional data, default vehicle-miles traveled mix by vehicle class in mobile emission inventory models is usually used in transportation emissions inventory estimates. Results from such practice, however, are often far from accurate. Heavy-duty trucks generate orders of magnitudes higher emission rates than light duty vehicles. Vehicle classification data collected from weigh-in-motion stations in California are used to examine the performance of various forms of the method across days of week and geographic areas. We find that the models identified provide satisfactory and statistically robust estimates of truck traffic.     

Estimation of saturation flow at signalised intersections of developing cities: a micro-simulation modelling approach

Traffic characteristics and operations at the signalised intersections of developing cities are significantly different from those at the similar intersections of cities in developed countries. Considering this, a new microscopic simulation technique, where a co-ordinate approach to modelling vehicle location is adopted, has been used for modelling the traffic operations at signalised intersections of developing cities. The model has been calibrated and validated on the basis of data collected from Dhaka, the capital of Bangladesh. It has been found that the concept of passenger car unit (PCU), which is widely used as a signal design parameter, is not applicable in case of mixed traffic comprising of both motorised and non-motorised vehicles. Therefore, using the developed simulation model the saturation flows at signalised intersections are investigated in an aggregate form of vehicles per hour. It has also been found that saturation flows in terms of aggregate vehicles are very much dependent on the approach width, turning proportion and composition of the traffic mix. Using the simulation results, an equation has also been regressed in order to be able to estimate the saturation flow from the influencing variables like road width, turning proportion, percentage of heavy and non-motorised vehicles.     

The effect of the competition between cars and trucks on the evolution of the motorway transport system

Motorways, which were devised at the beginning of their history as dedicated roads intended to be traveled by cars only, are at present also traveled by considerable flows of trucks. This fact has deeply changed the motorway transport system with respect to its original conception, owing to the interactions between two categories of vehicles whose characteristics are very different. These interactions greatly increase the transport cost perceived by car drivers with respect to truck drivers. This paper studies the consequences of this cost asymmetry on the evolution of the transport system when the geometric characteristics of a motorway remain unchanged in time, while transport demand increases. By using a theoretical model of competition between cars and trucks, it is shown that, if both the geometric characteristics of a motorway and the increase rate of the activities that feed the transport demand remain unchanged over time, the competition between cars and trucks, as well as the fact that in general passengers have better transport alternatives than freight, make the increase rate of truck traffic greater than that of cars, causing a progressive increase in the proportion of trucks in the time periods in which a motorway is traveled by both the vehicle categories. Since truck traffic on motorways, at least in Europe, is very scarce on weekends and in holiday periods, in which motorways are traveled almost only by cars, these results seem to indicate a tendency to the specialization of motorways, which are likely to be used in the future mostly by only one category of vehicles in different periods of time.     

Including heavy vehicles in a car‐following model: modelling,calibrating and validating

Heavy vehicles influence general traffic in many different ways compared with passenger vehicles, and this may result in different levels of traffic instability. Increases in the number and proportion of heavy vehicles in the traffic stream will therefore result in different traffic flow conditions. This research initially outlines the different car‐following behaviour of drivers in congested heterogeneous traffic conditions indicating the necessity for developing a car‐following model, which includes these differences. A psychophysical car‐following model, similar in form to Weideman's car‐following model, was developed. Due to the complexity of the developed model, the calibration of the model was undertaken using a particle swarm optimisation algorithm with the data recorded under congested traffic conditions. This was then incorporated into a traffic microsimulation model. The results showed that the car‐following perceptual thresholds and thus action points of drivers differ based on their vehicle and the lead vehicle types. The inclusion of the heavy vehicles in the model showed significant impacts on the traffic dynamic and interactions amongst different vehicles. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of road width and traffic volume on vehicular interactions in heterogeneous traffic

Highway traffic flow phenomena involve several complex and stochastic variables with high interdependencies. The variations in roadway, traffic and environmental factors influence the traffic flow quality significantly. Capacity analysis of road sections under different traffic and geometric conditions need to quantify the vehicles of widely varying characteristics to a common and universally acceptable unit. Passenger car unit (PCU) is the universally adopted unit of traffic volume, keeping the passenger car as the ‘standard vehicle’ with reference to its static and dynamic characteristics; other vehicles are expressed to its equivalent number in terms of PCUs. The studies carried out in this aspect represent the dynamic nature of impedance caused by a vehicle while moving through a traffic stream. The PCU values recommended by the Highway Capacity Manual are widely applied in many countries; however, their applicability is highly under debate because of the variations in prevailing local traffic conditions. There are several factors that influence the PCU values such as traffic, roadway, vehicle, environmental and control conditions, etc. Apart from vehicular characteristics, the other two major factors that influence the PCU of vehicles are the following: (i) road width and (ii) traffic volume. In this study, estimation of PCU values for the different types of vehicles of a highly heterogeneous traffic on 7.5‐ and 11.0‐m‐wide roads, using micro‐simulation technique, has been dealt with. It has been found that the PCU value of a vehicle type varies significantly with variation in road width and traffic volume. The results of the study indicate that the PCU values are significantly influenced by the said two factors. Copyright © 2012 John Wiley & Sons, Ltd.     

Profit maximization by a private toll road with cars and trucks

This paper examines the profit maximizing behavior of a private firm which operates a toll road competing against a free alternative in presence of cars and trucks. Trucks differ from cars in value of time (VOT), congestion externality, pavement damage, and link travel time function. We find that the firm takes either a car-strategy or a truck-strategy for profit maximization. For a traffic mix with relatively large car volume and small truck volume, the car-strategy results in no trucks using the toll road, while the truck-strategy results in all trucks using the toll road. We derive the equilibrium flow pattern under any combination of car-toll and truck-toll, based on which we identify a profit-maximizing frontier and a strategy-switching frontier in the car-toll and truck-toll two-dimensional space. By geometrically comparing the two frontiers, we establish general conditions under which each strategy will be taken, which suggest that the truck-to-car VOT ratio, the total traffic demand, and the difference in travel distance between the two roads are critical in shaping the firm's strategy.     

Improvement of the volume-delay function by incorporating the impact of trucks on traffic flow

In current transportation modelling, travel time is the most important factor in decisions regarding transport modes, destinations and routes. The calculation of travel time is deployed by volume-delay functions (VDFs), a sub-model of route assignment procedure, using the correlation between increasing numbers of vehicles on a road and the road's restrictive capacity. By investigating existing VDFs, a clear gap is seen, demonstrating that current functions are not suited to reflect the empirically known large impact of trucks on passenger car travel times. This issue becomes crucial when transport models are used to reflect future scenarios where goods transportation is expected to increase greatly, and when transport models combine passenger and commercial traffic. This paper presents a new VDF which successfully includes trucks’ impact on traffic flow in the case of Germany and, with slight deviations, for North America. The function is developed using ideal-type data for German motorways. The differences between German and US data and their implications for VDFs are also discussed.     

Multi-modal traffic signal control with priority,signal actuation and coordination

Both coordinated-actuated signal control systems and signal priority control systems have been widely deployed for the last few decades. However, these two control systems are often conflicting with each due to different control objectives. This paper aims to address the conflicting issues between actuated-coordination and multi-modal priority control. Enabled by vehicle-to-infrastructure (v2i) communication in Connected Vehicle Systems, priority eligible vehicles, such as emergency vehicles, transit buses, commercial trucks, and pedestrians are able to send request for priority messages to a traffic signal controller when approaching a signalized intersection. It is likely that multiple vehicles and pedestrians will send requests such that there may be multiple active requests at the same time. A request-based mixed-integer linear program (MILP) is formulated that explicitly accommodate multiple priority requests from different modes of vehicles and pedestrians while simultaneously considering coordination and vehicle actuation. Signal coordination is achieved by integrating virtual coordination requests for priority in the formulation. A penalty is added to the objective function when the signal coordination is not fulfilled. This “soft” signal coordination allows the signal plan to adjust itself to serve multiple priority requests that may be from different modes. The priority-optimal signal timing is responsive to real-time actuations of non-priority demand by allowing phases to extend and gap out using traditional vehicle actuation logic. The proposed control method is compared with state-of-practice transit signal priority (TSP) both under the optimized signal timing plans using microscopic traffic simulation. The simulation experiments show that the proposed control model is able to reduce average bus delay, average pedestrian delay, and average passenger car delay, especially for highly congested condition with a high frequency of transit vehicle priority requests.     

Modeling delay at signalized intersections with channelized right‐turn lanes considering the impact of blockage

This paper presents a probabilistic delay model for signalized intersections with right‐turn channelization lanes considering the possibility of blockage. Right‐turn channelization is used to improve the capacity and to reduce delay at busy intersections with a lot of right‐turns. However, under heavy traffic conditions the through vehicles will likely block the channelization entrance that accrues delay to right‐turn vehicles. If the right‐turn channelization gets blocked frequently, its advantage in reducing the intersection delay is neglected and as a result the channelization lane becomes inefficient and redundant. The Highway Capacity Manual (HCM) neglects the blockage effect, which may be a reason for low efficiency during peak hours. More importantly, using HCM or other standard traffic control methods without considering the blockage effects would lead to underestimation of the delay. To overcome this issue, the authors proposed delay models by taking into account both deterministic and random aspects of vehicles arrival patterns at signalized intersections. The proposed delay model was validated through VISSIM, a microscopic simulation model. The results showed that the proposed model is very precise and accurately estimates the delay. In addition, it was found that the length of short‐lane section and proportion of right‐turn and through traffic significantly influence the approach delay. For operational purposes, the authors provided a step‐by‐step delay calculation process and presented approach delay estimates for different sets of traffic volumes, signal settings, and short‐lane section lengths. The delay estimates would be useful in evaluating adequacy of the current lengths, identifying the options of extending the short‐lane section length, or changing signal timing to reduce the likelihood of blockage. Copyright © 2016 John Wiley & Sons, Ltd.     

A study on adjustment factors for U-turns in left-turn lanes at signalized intersections

U-turns are treated as left-turns in the current procedures for estimating saturation flow rates at signalized intersections. While U-turning vehicles are usually mixed with left-turning vehicles in inside or left-turn lanes and conflict with opposing through traffic as left-turning vehicles, the vehicle operating characteristics are different. The objective of this paper is to investigate the effects of U-turns on the traffic flow in left-turn lanes. Field data of 600 headways of left-turning passenger cars and 160 headways of U-turning passenger cars are recorded. The average headways of U-turning passenger cars are found to be significantly larger than those of left-turning passenger cars. The effects of U-turning vehicles depend upon the percent of U-turning vehicles in the left-turn lane, as well as the order of formation in the traffic stream. Adjustment factors for varying percents of U-turning vehicles in left-turn lanes are established.     

Fatal crash involvement by multiple-trailer trucks

Considerable uncertainty surrounds the relative safety of combination trucks with two or three trailers, compared to those pulling single trailers. This article uses data on conditions present in 5889 fatal crashes involving combination trucks to examine the extent to which these conditions vary for the two configurations. Using two complementary techniques, multiple classification analysis and automatic interaction detector, we evaluate the additive and interactive effects of these conditions. We conclude that multiple-trailer trucks are more likely to be involved in fatal crashes in the following conditions: darkness; snow, slush, or ice on the road surface; involvement of three or more vehicles, indicating at least moderate traffic volume; and higher-speed facilities with 65 to 75 mph limits.     

Transit assignment under crowded conditions

This paper presents a transit assignment algorithm for crowded networks. Both congestion in vehicles and queuing at stations are explicitly taken into account in predicting passenger flows for a fixed pattern of origin-destination trip demands. The overflow effects due to insufficient capacity of transit lines are considered to be concentrated at transit stations, while the in-vehicle congestion effects (or discomforts) are considered to be dependent on in-vehicle passenger volume. Overflow delay at a transit station is dependent on the number of excess passengers required to wait for the next transit car. We use a logit model to determine the split between passengers that chose to wait for the next transit car and passengers that chose to board on the alternative transit lines. The proposed algorithm predicts how passenger will choose their optimal routes under both queuing and crowded conditions.