Improvement of the volume-delay function by incorporating the impact of trucks on traffic flow

In current transportation modelling, travel time is the most important factor in decisions regarding transport modes, destinations and routes. The calculation of travel time is deployed by volume-delay functions (VDFs), a sub-model of route assignment procedure, using the correlation between increasing numbers of vehicles on a road and the road's restrictive capacity. By investigating existing VDFs, a clear gap is seen, demonstrating that current functions are not suited to reflect the empirically known large impact of trucks on passenger car travel times. This issue becomes crucial when transport models are used to reflect future scenarios where goods transportation is expected to increase greatly, and when transport models combine passenger and commercial traffic. This paper presents a new VDF which successfully includes trucks’ impact on traffic flow in the case of Germany and, with slight deviations, for North America. The function is developed using ideal-type data for German motorways. The differences between German and US data and their implications for VDFs are also discussed.     

Delay-based passenger car equivalents for trucks at signalized intersections

This paper presents a new methodology for computing passenger car equivalents at signalized intersections that is based on the delay concept. Unlike the commonly used headway-based methods that consider only the excess headway consumed by trucks, the delay-based approach fully considers the additional delay heavy vehicles cause on traffic stream. Delay-based passenger car equivalents are not constant, but depend on traffic volume, truck type and truck percentage. The field data indicated that the passenger car equivalents increase as the traffic volume and the percentage of heavy vehicles increase. The field data were used to calibrate TRAF-NETSIM simulation model that was used to cover a broad range of traffic conditions. Mathematical models to estimate the equivalencies were developed. The passenger car equivalent for single unit trucks vary from 1.00 to 1.37, and for combination trucks 1.00–2.18 depending on traffic volume and truck percentage. The passenger car equivalents are highly correlated with traffic volume and, to some degree, with percentage of heavy vehicles. Although the PCE of 1.5 recommended in the 1985 HCM seems to be more reasonable than the 2.0 recommended in the 1994 and 1997 HCM, both overestimate the impact of single unit trucks. For combination trucks, the 1997 HCM overestimates the capacity reduction effects of the trucks in most cases.     

Characteristics of truck traffic in Singapore

This paper presents the results of a project conducted to study the characteristics of truck traffic in Singapore. Detailed traffic surveys recording counts of vehicles by axle-configuration were performed at 219 sites over a period of nearly two years. The surveys covered 5 different road classes, namely expressways, arterials, collectors, industrial roads and local roads. It was found that the time distribution of truck travel were not the same among the five road classes. The peaking characteristics of truck traffic were less pronounced compared to passenger car traffic. The peak hour truck volume varied from 67.0% to 9.7% of the daily truck traffic as compared to 13.8% for passenger car traffic. The lane distribution pattern of truck traffic was studied in detail by road class, and was found to be a function of total directional traffic volume, total directional truck volume and the number of traffic lanes. Composition analysis was also carried out to study the lane use characteristics of single- and multiple-unit trucks.     

Improving estimates of transportation emissions: Modeling hourly truck traffic using period-based car volume data

We estimate hourly truck traffic using period-based car volumes that are usually available from travel demand models. Due to the lack of local or regional data, default vehicle-miles traveled mix by vehicle class in mobile emission inventory models is usually used in transportation emissions inventory estimates. Results from such practice, however, are often far from accurate. Heavy-duty trucks generate orders of magnitudes higher emission rates than light duty vehicles. Vehicle classification data collected from weigh-in-motion stations in California are used to examine the performance of various forms of the method across days of week and geographic areas. We find that the models identified provide satisfactory and statistically robust estimates of truck traffic.     

货车自动驾驶技术及标准法规发展分析

目前,自动驾驶技术在乘用车领域已获得突破性发展;为提高通行效率和出行安全起到了极大的作用。自动驾驶技术在商用车领域的应用,有望较好解决高昂的人力成本和难以提高的效率等问题。然而,目前自动驾驶技术在货车的应用大多采用跟乘用车同样的标准进行规范,这在实际应用中存在着诸多的问题;例如,在FCW和AEB功能中货车在相同车速的制动距离要远大于乘用车,而其所采用标准规定的碰撞预警时间却并无多大不同,这在实际场景中存在着较大的安全隐患[1,2]。此外,货车质量和体积较大,且较多应用于长途运输,运输过程中会经历包括高温、严寒、山区等多种复杂气候场景,这些都将对货车自动驾驶技术在车辆制动效能、能耗以及多场景应用等方面提出更有针对性规范的要求。本文针对货车的应用场景特点,为其自动驾驶技术应用标准化提出了建议。     

Motorway crash duration and its determinants: do durations vary across motorways?

Traffic congestion has been a growing issue in many metropolitan areas during recent years, which necessitates the identification of its key contributors and development of sustainable strategies to help decrease its adverse impacts on traffic networks. Road incidents generally and crashes specifically have been acknowledged as the cause of a large proportion of travel delays in urban areas and account for 25% to 60% of traffic congestion on motorways. Identifying the critical determinants of travel delays has been of significant importance to the incident management systems, which constantly collect and store the incident duration data. This study investigates the individual and simultaneous differential effects of the relevant determinants on motorway crash duration probabilities. In particular, it applies parametric Accelerated Failure Time (AFT) hazard‐based models to develop in‐depth insights into how the crash‐specific characteristic and the associated temporal and infrastructural determinants impact the duration. AFT models with both fixed and random parameters have been calibrated on one year of traffic crash records from two major Australian motorways in South East Queensland, and the differential effects of determinants on crash survival functions have been studied on these two motorways individually. A comprehensive spectrum of commonly used parametric fixed parameter AFT models, including generalized gamma and generalized F families, has been compared with random parameter AFT structures in terms of goodness of fit to the duration data, and as a result, the random parameter Weibull AFT model has been selected as the most appropriate model. Significant determinants of motorway crash duration included traffic diversion requirement, crash injury type, number and type of vehicles involved in a crash, day of week and time of day, towing support requirement and damage to the infrastructure. A major finding of this research is that the motorways under study are significantly different in terms of crash durations; such that motorway 1 exhibits durations that are on average 19% shorter compared with the durations on motorway 2. The differential effects of explanatory variables on crash durations are also different on the two motorways. The detailed presented analysis confirms that looking at the motorway network as a whole, neglecting the individual differences between roads, can lead to erroneous interpretations of duration and inefficient strategies for mitigating travel delays along a particular motorway.     

Impact of heavy vehicles on surrounding traffic characteristics

This work examines the impact of heavy vehicle movements on measured traffic characteristics in detail. Although the number of heavy vehicles within the traffic stream is only a small percentage, their impact is prominent. Heavy vehicles impose physical and psychological effects on surrounding traffic flow because of their length and size (physical) and acceleration/deceleration (operational) characteristics. The objective of this work is to investigate the differences in traffic characteristics in the vicinity of heavy vehicles and passenger cars. The analysis focuses on heavy traffic conditions (level of service E) using a trajectory data of highway I‐80 in California. The results show that larger front and rear space gaps exist for heavy vehicles compared with passenger cars. This may be because of the limitations in manoeuvrability of heavy vehicles and the safety concerns of the rear vehicle drivers, respectively. In addition, heavy vehicle drivers mainly keep a constant speed and do not change their speed frequently. This work also examines the impact of heavy vehicles on their surrounding traffic in terms of average travel time and number of lane changing manoeuvres using Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Networks (AIMSUN) microscopic traffic simulation package. According to the results, the average travel time increases when proportion of heavy vehicles rises in each lane. To reflect the impact of heavy vehicles on average travel time, a term related to heavy vehicle percentage is introduced into two different travel time equations, Bureau of Public Roads and Akçelik's travel time equations. The results show that using an exclusive term for heavy vehicles can better estimate the travel times for more than 10%. Finally, number of passenger car lane changing manoeuvres per lane will be more frequent when more heavy vehicles exist in that lane. The influence of heavy vehicles on the number of passenger car lane changing is intensified in higher traffic densities and higher percentage of heavy vehicles. Large numbers of lane changing manoeuvres can increase the number of traffic accidents and potentially reduce traffic safety. The results show an increase of 5% in the likelihood of accidents, when percentage of heavy vehicles increases to 30% of total traffic. Copyright © 2014 John Wiley & Sons, Ltd.     

Influence of vehicle driving parameters on the noise caused by passenger cars in urban traffic

In this work, a sample of vehicles has been instrumented to measure of variables that influence vehicle noise emissions in Madrid. A circuit reproducing a normal travel pattern in large city is traveled by a fleet of vehicle models representing the fleets of cars in a European city. A sample of drivers covers the test track under different traffic conditions. Driving parameters and noise emitted have been recorded in each test and average values have been extracted. These data have been analyzed to define the noise emissions produced by a vehicle in real driving conditions and to identify the noisiest driving behaviors.     

An econometric analysis of motorway renewal costs in Germany

The analysis of motorway renewal costs presented in this paper was driven by two research questions: First, to analyse the economic process of motorway renewal work and to identify whether there exist economies of scale; and second to identify the influence of traffic volume on renewal costs and to derive an estimate of marginal infrastructure costs as part of optimal road user charges. The analysis is based on cross-sectional data for motorway renewal costs and traffic volume in Germany during the period 1980–1999. Two translog models were estimated, each of them including the factor input prices for labour, material and capital, and a set of regional dummy variables as well as dummy variables for the type of material used for renewal. The first model includes in addition to these variables the sqm of renewed road as explanatory variable. The second model was constructed to analyse the relationship between traffic volume and renewal costs and contains the average annual daily traffic volume of trucks and passenger cars as independent variables. Two main results were derived from the models: First, motorway renewal work is characterised by substantial economies of scale. Second, the relationship between renewal costs and traffic volume is expressed by a cost elasticity, i.e., the ratio between marginal and average costs, which ranges from 0.05 up to 1.17 with a digressive increase of marginal costs.     

Preferences for autonomous and alternative fuel-powered heavy-duty trucks in Germany

Germany is by far the largest contributor of greenhouse gas emissions in the European Union but adopted its own climate action plan to achieve greenhouse gas neutrality by 2050. The country’s third-largest emitter of greenhouse gas emissions is the transportation sector. As of January 2019, 99.7% of heavy-duty trucks registered in Germany run on diesel while the share of alternative fuel-powered passenger cars increases steadily. Apart from rising emissions, the industry faces a growing shortage of qualified truck drivers. A solution to increasing emissions and the shortage of drivers are autonomous and alternative fuel-powered heavy-duty trucks. We employed a choice-based conjoint analysis with employees from freight companies in Germany to find out how they assess the main attributes of innovative trucks. Our results reveal that the maximum driving range is the most important attribute followed by the refueling/recharging time. Tank-to-wheel emissions, on the other hand, was ranked as the least relevant attribute. Moreover, we present customers’ preference shares for future heavy-duty trucks until 2035. According to our results, freight companies are generally open to switching from conventional to low emission and (conditionally-) automated heavy-duty trucks, however, a close collaboration between truck manufacturers, customers, infrastructure companies, and policymakers is essential to spur the penetration of autonomous and alternative fuel-powered heavy-duty trucks.     

Analysis of a cooperative variable speed limit system using microscopic traffic simulation

Variable speed limit systems where variable message signs are used to show speed limits adjusted to the prevailing road or traffic conditions are installed on motorways in many countries. The objectives of variable speed limit system installations are often to decrease the number of accidents and to increase traffic efficiency. Currently, there is an interest in exploring the potential of cooperative intelligent transport systems including communication between vehicles and/or vehicles and the infrastructure. In this paper, we study the potential benefits of introducing infrastructure to vehicle communication, autonomous vehicle control and individualized speed limits in variable speed limit systems. We do this by proposing a cooperative variable speed limit system as an extension of an existing variable speed limit system. In the proposed system, communication between the infrastructure and the vehicles is used to transmit variable speed limits to upstream vehicles before the variable message signs become visible to the drivers. The system is evaluated by the means of microscopic traffic simulation. Traffic efficiency and environmental effects are considered in the analysis. The results of the study show benefits of the infrastructure to vehicle communication, autonomous vehicle control and individualized speed limits for variable speed limit systems in the form of lower acceleration rates and thereby harmonized traffic flow and reduced exhaust emissions.     

Point-to-point speed enforcement systems: Speed limits design criteria and analysis of drivers’ compliance

Point-to-point (P2P) speed enforcement is a relatively new approach to traffic law enforcement. Its technology allows vehicles whose average speed exceeds the speed limit over the controlled section to be fined. It therefore encourages compliance over distances longer than those where spot enforcement policies have been in place.In this paper, a procedure for consistently setting speed limits with such enforcement systems is proposed. Such a method has been applied to design the speed limits on two motorways in the district of Naples, Italy, where P2P enforcement systems became operational in 2009 and 2010. The speed limits, which were set using the Italian geometric design standard to assess vehicle stability and stopping sight distance, have been compared with those provided by using well-known international standards.The impact of the newly designed speed limits and of the P2P enforcement system on drivers’ speeding behaviour has been quantified for each highway section and vehicle type. In fact, accurate measurements of the average travel speeds of each vehicle crossing the enforced sections, before and after the activation of the system, were available. The migration from the old speed limits with spot speed enforcement to the new approach resulted in a notable increase in drivers’ compliance to the speed limits with a remarkable decrease in both the average of individual speeds and in their standard deviation.In addition, the analysis of 3 years of data shows that a gradual adaptation of drivers’ behaviour to the system took place. In particular, a decreasing compliance to the speed limits points to a non-optimal system management. Finally, the results of a revealed preference survey allowed us to make a behavioural interpretation regarding the significantly different impacts measured on the two motorways.     

Profit maximization by a private toll road with cars and trucks

This paper examines the profit maximizing behavior of a private firm which operates a toll road competing against a free alternative in presence of cars and trucks. Trucks differ from cars in value of time (VOT), congestion externality, pavement damage, and link travel time function. We find that the firm takes either a car-strategy or a truck-strategy for profit maximization. For a traffic mix with relatively large car volume and small truck volume, the car-strategy results in no trucks using the toll road, while the truck-strategy results in all trucks using the toll road. We derive the equilibrium flow pattern under any combination of car-toll and truck-toll, based on which we identify a profit-maximizing frontier and a strategy-switching frontier in the car-toll and truck-toll two-dimensional space. By geometrically comparing the two frontiers, we establish general conditions under which each strategy will be taken, which suggest that the truck-to-car VOT ratio, the total traffic demand, and the difference in travel distance between the two roads are critical in shaping the firm's strategy.     

Impacts of highly automated vehicles on travel demand: macroscopic modeling methods and some results

Automated vehicles (AV) will change transport supply and influence travel demand. To evaluate those changes, existing travel demand models need to be extended. This paper presents ways of integrating characteristics of AV into traditional macroscopic travel demand models based on the four-step algorithm. It discusses two model extensions. The first extension allows incorporating impacts of AV on traffic flow performance by assigning specific passenger car unit factors that depend on roadway type and the capabilities of the vehicles. The second extension enables travel demand models to calculate demand changes caused by a different perception of travel time as the active driving time is reduced. The presented methods are applied to a use case of a regional macroscopic travel demand model. The basic assumption is that AV are considered highly but not fully automated and still require a driver for parts of the trip. Model results indicate that first-generation AV, probably being rather cautious, may decrease traffic performance. Further developed AV will improve performance on some parts of the network. Together with a reduction in active driving time, cars will become even more attractive, resulting in a modal shift towards car. Both circumstances lead to an increase in time spent and distance traveled.

     

Heavy commercial vehicles‐following behavior and interactions with different vehicle classes

This work investigates the effect of heavy commercial vehicles on the capacity and overall performance of congested freeway sections. Furthermore, the following behaviors of heavy commercial vehicles and its comparison with passenger cars are presented. Freeways are designed to facilitate the flow of traffic including passenger cars and trucks. The impact of these different vehicle types is not uniform, creating problems in freeway operations and safety particularly under heavy demand with a high proportion of heavy vehicles. There have been very few studies concerned with the traffic behavior and characteristics of heavy vehicles in these situations. This study draws on extensive data collected over a long stretch of freeway using videotaping and surveys at several sites. The collected data were firstly used to study the interaction between heavy vehicles and passenger cars. Through a detailed trajectory analysis, the following behaviors of 120 heavy vehicles were then analyzed to provide a thorough understanding of heavy vehicles‐following behavior mechanism. The results showed a significant difference in the following behavior of heavy vehicles compared with other vehicles. Copyright © 2011 John Wiley & Sons, Ltd.     

A Cooperative Intelligent Transport Systems (C‐ITS)‐based lane‐changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane‐change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane‐changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C‐ITS). This research investigates a lane‐change distribution advisory application based on C‐ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane‐changing concentration problem by coordinating weaving vehicles to ensure that such lane‐changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in aimsun to evaluate the proposed strategy's effectiveness in a one‐sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane‐changing advisory has the potential to significantly improve delay. Copyright © 2016 John Wiley & Sons, Ltd.     

Driving speeds in Europe for pollutant emissions estimation

The sensitivity of the pollutant emissions as regards the driving speed is demonstrated using emission functions currently available from the literature. An accurate and detailed knowledge of the actual driving speeds is then fundamental for emissions estimations and inventories. However, speed information is often limited and heterogeneous. Through a European synthesis, we examine the various means of investigations: surveys, vehicle instrumentation, traffic modelling, etc.The available statistics provide a high number of reference values for passenger cars and duty vehicles by broad categories and highlight the influence of numerous factors on speed: time period, city size and area, trips origin and destination and vehicle types. Speed estimations and ranges are proposed for the driving in urban areas, on rural roads and on motorways.The significant variations of the speed according to the time of the day, to the areas of a city, and the large dispersion for a given situation raise the question of using single average values. In fact, emissions estimation can be affected by 30% by the quality of the driving speed data.     

Real-time merging traffic control for throughput maximization at motorway work zones

Work zones on motorways necessitate the drop of one or more lanes which may lead to significant reduction of traffic flow capacity and efficiency, traffic flow disruptions, congestion creation, and increased accident risk. Real-time traffic control by use of green–red traffic signals at the motorway mainstream is proposed in order to achieve safer merging of vehicles entering the work zone and, at the same time, maximize throughput and reduce travel delays. A significant issue that had been neglected in previous research is the investigation of the impact of distance between the merge area and the traffic lights so as to achieve, in combination with the employed real-time traffic control strategy, the most efficient merging of vehicles. The control strategy applied for real-time signal operation is based on an ALINEA-like proportional–integral (PI-type) feedback regulator. In order to achieve maximum performance of the control strategy, some calibration of the regulator’s parameters may be necessary. The calibration is first conducted manually, via a typical trial-and-error procedure. In an additional investigation, the recently proposed learning/adaptive fine-tuning (AFT) algorithm is employed in order to automatically fine-tune the regulator parameters. Experiments conducted with a microscopic simulator for a hypothetical work zone infrastructure, demonstrate the potential high benefits of the control scheme.     

The effects of in-car speed limiters: field studies

Field trials in three European countries, the Netherlands, Spain and Sweden were carried out in order to investigate the effects of an in-car speed limiter. The trials were carried out on urban and rural roads including motorways. A so-called unobtrusive instrumented car was used, where all the measuring equipment was hidden. All the speed limit categories in the respective countries, ranging from 30 to 120 km/h were included. The results showed that the effects of the limiter were greatest in free driving conditions outside platoons. However, the limiter also had effects in congested traffic. Momentary high speeds were suppressed effectively, which resulted in less variation of speeds. Approach speeds at roundabouts, intersections and curves became smoother, car-following behaviour became safer in the speed range of 30–50 km/h. On the other hand, in the speed range of 70–90 km/h a slightly higher number of short time-gaps suggested less safe car-following behaviour. Other negative behavioural effects were slightly increased travel time and the increased frustration and stress for the drivers caused by the limiter. The majority of the subjects accepted the speed limiter as a driver-operated system. Half of the drivers would accept the limiter voluntarily in their cars.     

Implications of driving style and road grade for accurate vehicle activity data and emissions estimates

Real-world vehicle operating mode data (2.5 million 1 Hz records), collected by instrumenting the vehicles of 82 volunteer drivers with OBD datalogger and GPS while they drove their routine travel routes, were analyzed to quantify vehicle emissions estimate errors due to road grade and driving style in rural, hilly Vermont. Data were collected in winter and summer for MY 1996 and newer passenger cars and trucks only. EPA MOVES2010b was used to estimate running exhaust emissions associated with measured vehicle activity. Changes in vehicle specific power (VSP) and MOVES operating mode (OpMode) due to proper accounting for real-world road grade indicated emission rate errors between 10% and 48%, depending on pollutant, chiefly because grade-related changes in VSP could shift activity by as many as six OpModes, depending on road type. The correct MOVES OpMode assignment was made only 33–55% of the time when road grade was not included in the VSP calculation. Driving style of individual drivers was difficult to assess due to unknown traffic operations data, but the largest differences between individual drivers were observed on rural restricted roads, where traffic conditions and control have minimal impact. The results suggest the importance of (1) measuring and incorporating real-world road grade in order to correctly assign MOVES emission rates; and (2) developing a driving style typology to account for differences in the MOVES emissions estimates due to driver variability.