Ultimate hull girder strength of a bulk carrier under combined global and local loads in the hogging and alternate hold loading condition using nonlinear finite element analysis

For bulk carriers in hogging, the most critical situation is the alternate hold loading (AHL) condition with odd numbered holds loaded with high density cargoes and even numbered holds empty. The effect of the local lateral pressure loads should be considered in the assessment of ultimate hull girder strength in the hogging and AHL conditions. In the present paper the ultimate strength of a Capesize bulk carrier hull girder under combined global and local loads in the hogging and AHL condition is extensively and systematically investigated using nonlinear finite element (FE) analysis with ABAQUS software. Since the bulk carrier used as a reference vessel in this study is an old design we also studied the effect of modified scantlings by multiplying the plate thickness in the bottom structure by a design modification factor (DMF). In particular, it should be noted that a DMF of 1.4 gives a design in accordance with the new CSR rules. Based on the results obtained by nonlinear FE analyses, a practical interaction equation is established between global hogging bending capacity and average external sea pressure over the bottom.     

Ultimate strength of container ships subjected to combined hogging moment and bottom local loads part 1: Nonlinear finite element analysis

This paper is the first of two companion papers concerning the ultimate hull girder strength of container ships subjected to combined hogging moment and bottom local loads. In the midship part of container ships, upward bottom local loads are usually larger than the downward ones. This leads to the increase of biaxial compression in the outer bottom plating and the reduction of the ultimate hull girder strength in the hogging condition. In this Part 1, the collapse behavior and ultimate strength of container ships under combined hogging moment and bottom local loads are analyzed using nonlinear finite element method. Buckling collapse behavior of bottom stiffened panels during the progressive collapse of a hull girder is closely investigated. It has been found that major factors of the reduction of ultimate hogging strength due to bottom local loads are (1) the increase of the longitudinal compression in the outer bottom and (2) the reduction of the effectiveness of the inner bottom, which is on the tension side of local bending of the double bottom. The obtained results will be utilized in the Part 2 paper to develop a simplified method of progressive collapse analysis of container ships under combined hogging moment and bottom local loads.     

Ultimate strength of container ships subjected to combined hogging moment and bottom local loads,Part 2: An extension of Smith's method

This paper is the second of two companion papers concerning the ultimate hull girder strength of container ships subjected to combined hogging moment and bottom local loads. The nonlinear finite element analysis in Part 1 has shown that local bending deformation of a double bottom due to bottom lateral loads significantly decreases the ultimate hogging strength of container ships. In this Part 2, extending Smith's method for pure bending collapse analysis of a ship's hull girder, a simplified method of progressive collapse analysis of ultimate hogging strength of container ships considering bottom local loads is developed. The double bottom is idealized as a plane grillage and the rest part of the cross section as a prismatic beam. An average stress-average strain relationship of plate/stiffened plate elements employed in Smith's method is transformed into an average stress-average plastic strain relationship, and implemented in the conventional beam finite element as a pseudo strain hardening/softening behaviors. The extended Smith's method is validated through a comparison with nonlinear finite element analysis.     

散货船隔舱重载下极限强度简易计算方法研究

散货船在装载矿石等重货时,通常只装载在奇数货舱内,这就是所谓的隔舱重载工况。在这种工况下,中间舱的双层底结构除受到总纵弯曲作用外,还会受到邻舱重货引起的局部弯曲作用,而且该局部弯曲的作用会降低中拱状态下船体梁的极限强度。文章提出了一种简易计算方法,顶边舱结构和底边舱结构可以看作两根梁,双层底结构可视作正交异性板,运用双梁理论和正交异性板理论可推导出局部弯曲的影响。然后,考虑该局部弯曲的作用,用Smith法计算船体梁的极限强度。最后,将文中方法计算的结果与FEM结果进行比较,并对结果进行了分析。     

Reliability analysis of a bulk carrier in ultimate limit state under combined global and local loads in the hogging and alternate hold loading condition

The alternate hold still-water loading in hogging combined with wave loading is critical for the safe design of bulk carriers. The ultimate longitudinal strength of the hull girder of bulk carriers in this condition has been found to be considerably reduced by the action of local lateral pressure loads. In the present paper, an interaction equation based on the ultimate hull girder strength assessment obtained by nonlinear finite element analyses is adopted to consider the relationship between ultimate longitudinal bending capacity and average external sea pressure over the bottom. This interaction equation is used as the basis for the failure function. The annual probability of failure is obtained by FORM analysis considering two typical load cases, namely, pure longitudinal hogging bending moment and combined global hogging bending moment and local lateral pressure loads. The effect of heavy weather avoidance on the failure probability is evaluated. The results show that the local lateral pressure has a significant influence on the annual probability of failure of bulk carriers in the hogging and alternate hold loading condition.     

CSR-H与CSR强度评估载荷的对比研究

对CSR-H 与CSR用于强度分析的载荷变化进行分析,对各载荷分量的包络值以及应用于等效设计波中的船体梁波浪弯矩、波浪剪力和外部海水压力、加速度等载荷分量的大小进行比较。分析货油舱、干散货舱、压载舱典型位置处的内部压力变化,并对载荷变化可能引起的结构要求变化进行分析和概括。     

基于完整船体极限强度和搁浅剩余强度的协调共同结构规范对比分析

文章基于Smith法,根据国际船级社协会发布的2013版协调共同结构规范(HCSR)中破损模型、失效模式和载荷模型,考虑材料屈服、结构单元屈曲及后屈曲的特性,应用FORTRAN程序设计语言编写船体极限强度计算程序,以某76000吨散货船为算例,对完整船体的极限强度进行计算,对搁浅状态下破损船体的剩余强度进行计算并校核承载能力。通过在中拱和中垂工况下与其他规范的对比验证,2013版HCSR指定的剩余强度校核公式及船体梁载荷计算公式中选取的安全系数要求更高,校核更严格。     

散货船碰撞损伤后的剪切极限强度

船体梁受到碰撞损伤后,必须有足够的剩余强度用以抵抗最大外弯矩,同时还需能够承受最大剪力.在众多类型的船舶中,散货船是一种抗剪能力较差的船型.对于其碰撞损伤后纵向剩余极限弯矩的研究已有较多的文献[2-7],而对于碰撞损伤后的剪切极限强度的研究目前还比较少.针对这一现状,本文的主要目的在于分析讨论散货船受到碰撞损伤后的极限承剪能力;分析结构几何尺寸,碰撞损伤形状以及边界条件等各种因素对碰撞破损船体抗剪能力的影响.为了方便起见,文中也给出了相应的回归经验公式.本文同时还推导了一个船体梁碰撞损伤后的初始屈服剪力计算公式.最后,本文以一艘散货船为例,计算分析其碰撞损伤后的抗剪能力,从中得出一些有益的结论.     

循环弯曲载荷下船体梁的极限纵强度

根据生破坏的强度准则，详细讨论了循环弯曲载荷下船体梁的非弹性变形性能。给出了循环弯曲载荷下船体梁极限强度的简化分析方法。进行了纵筋加强箱形薄壁梁模型的循环弯曲试验。理论计算与试验结果作了比较，两者吻合较好。     

不同损伤模式下的单舷侧散货船舷侧板架极限能力研究

对单舷侧散货船板架因装卸货物等受损后的结构极限承载能力的影响进行了研究,采用非线性有限元软件ABAQUS,建立单舷侧散货船板架完整模型和4种损伤模型,进行了舷侧板架在垂向载荷、船体纵向载荷、以及包括剪切和侧向压力的组合载荷作用下的非线性有限元计算。结果表明,因1根肋骨与板材之间连接的不同损伤,导致了相邻的其他肋骨工作应力不同程度的增加,或多或少地削弱了板架的承载能力,尤其在组合载荷的作用下,当一根肋骨的脱焊长度达肋骨长度的2/3时,板架极限承载力可下降15%。     

协调版共同结构规范对港口工况下散货船的影响分析

协调版共同结构规范（CSR-H）对港口工况下船体梁强度和船体构件局部强度的要求与先前的油船共同结构规范（CSR-OT）基本一致,而相比散货船共同结构规范（CSR-BC）有明显变化。通过对比分析CSR-H和CSR-BC对于港口工况具体要求的差异,并结合实船数据分析,阐述基于CSR-H要求的港口工况对散货船结构设计的影响;并探讨针对符合CSR-H的散货船,如何合理选取船体梁许用静水弯矩值和许用静水剪力值。     

波浪中船体梁后极限强度特性的实验评估(英文)

Experimental investigations into the collapse behavior of a box-shape hull girder subjected to extreme wave-induced loads are presented.The experiment was performed using a scaled model in a tank.In the middle of the scaled model,sacrificial specimens with circular pillar and trough shapes which respectively show different bending moment-displacement characteristics were mounted to compare the dynamic collapse characteristics of the hull girder in waves.The specimens were designed by using finite element(FE)-analysis.Prior to the tank tests,static four-point-bending tests were conducted to detect the load-carrying capacity of the hull girder.It was shown that the load-carrying capacity of a ship including reduction of the capacity after the ultimate strength can be reproduced experimentally by employing the trough type specimens.Tank tests using these specimens were performed under a focused wave in which the hull girder collapses under once and repetitive focused waves.It was shown from the multiple collapse tests that the increase rate of collapse becomes higher once the load-carrying capacity enters the reduction path while the increase rate is lower before reaching the ultimate strength.     

CFRP修复的FPSO点蚀船体梁极限强度分析

采用非线性有限元法对中拱和中垂工况条件下碳纤维增强聚合物(Carbon Fiber Reinforced Polymer, CFRP)修复的浮式生产储卸油装置(Floating Production Storage and Offloading, FPSO)点蚀船体梁极限强度进行仿真分析。对比FPSO的完整船体梁、点蚀船体梁和CFRP修复的点蚀船体梁的中拱极限弯矩和中垂极限弯矩，分析CFRP对FPSO点蚀船体梁的修复效果，并分析胶层失效规律。结果表明，CFRP可为船舶的高效修复提供一种新的方式。     

FLNG结构设计若干关键技术问题分析

总布置方案的特点决定了结构设计的特殊性和复杂性;从总强度分析的角度,讨论了船体梁载荷的确定方法和适用于薄膜舱应力衡准的船体梁剖面模数校核方法;从薄膜舱晃荡强度分析的角度,讨论了薄膜舱晃荡强度分析载荷和适用范围的确定方法;从有限元分析的角度,讨论了有限元强度评估范围和首、尾货舱加载工况,并总结了船体结构在有限元强度评估中发现的突出问题和解决方法。     

点蚀损耗对船体梁极限强度的影响（英文）

The paper focuses on the assessment of the hull girder ultimate strength,combined with random pitting corrosion wastage,by the incremental-iterative method.After a brief review about the state of art,the local ultimate strength of pitted platings under uniaxial compression is preliminarily outlined and subsequently a closed-form design formula is endorsed in the Rule incremental-iterative method,to account for pitting corrosion wastage in the hull girder ultimate strength check.The ISSC bulk carrier is assumed as reference ship in a benchmark study,devoted to test the effectiveness of the incremental-iterative method,by a comparative analysis with a set of FE simulations,performed by Ansys Mechanical APDL.Four reference cases,with different locations of pitting corrosion wastage,are investigated focusing on nine combinations of pitting and corrosion intensity degrees.Finally,a comparative analysis between the hull girder ultimate strength,combined with pitting corrosion wastage,and the relevant values,complying with the Rule net scantling approach,is performed.Based on current results,the modified incremental-iterative method allows efficiently assessing the hull girder ultimate strength,combined with pitting corrosion wastage,so revealing useful both in the design process of new vessels and in the structural health monitoring of aged ships.     

Progressive collapse analysis of ship hull girders subjected to extreme cyclic bending

This paper introduces a novel analytical method to predict the buckling collapse behaviour of a ship hull girder subjected to several cycles of extreme load. This follows the general principles of the established simplified progressive collapse method with an extended capability to re-formulate the load-shortening curve of structural components to account for cyclic degradation. The method provides a framework for assessing residual hull girder strength following a complex series of unusually extreme load events where the wave induced bending moment rises close to, or even surpasses, the monotonic ultimate strength. These load events may be sequential, such as might be caused by a series of storm waves, or they may occur as a collection of discrete events occurring over a longer period. The extreme cyclic bending amplifies the distortion and residual stress initially induced by fabrication in the flanges of the girder, which results in a deterioration of the residual ultimate strength. Validation is firstly completed through a comparison with previously published experimental work and secondly via comparison with numerical simulation on four ship-type box girders using the nonlinear finite element method.     

A proposal of reliability-based design formats for ultimate hull girder strength checks for bulk carriers under combined global and local loadings

The purpose of this paper is to provide a basis for the development of reliability-based design formats for ultimate hull girder strength checks for bulk carriers in hogging conditions under combined global and local loading and to estimate implied safety levels in current rule practices for hull girders. The effect of alternative definitions of characteristic still-water loads on the safety format and, hence, the safety factors is assessed. The effect of systematic (bias) model uncertainties associated with loads and strength on the reliability measures is investigated.     

双壳型船体结构稳态温度场和温度应力

用简化解析方法和有限元数值方法,分析了双壳型船体货舱区域在运载高温液货时的稳态温度场;根据船体结构的温度分布,用有限元法计算了其温度应力,同时与货物压力、海水静动压力、总纵弯矩等载荷作用下的结构应力做了比较。研究结果表明：在货舱结构温度场分析中用简化分析方法和有限元数值方法所得的计算结果相当一致;高温液货大幅度增加船体结构的纵向应力和横向应力,同时加剧结构不连续处的应力集中;槽型舱壁可以有效地释放     

Effect of pitting corrosion on the ultimate strength of steel plates subjected to in-plane compression and bending

Corrosion pits with a circular cone shape are typically observed on coated hold frames of aged bulk carriers which carry exclusively coal and iron ore. In order to ensure the safety of these types of bulk carrier, it is necessary to understand the effect of pitting corrosion on the local strength of hold frames. In order to investigate this effect, a series of nonlinear finite-element (FE) analyses has been performed with pitted plates subjected to in-plane compressive loads and bending moments. It has been shown that the ultimate compression load or bending moment of pitted plates is smaller than that of uniformly corroded plates in terms of average thickness loss, and that predictions of the ultimate strength using the average thickness loss at the minimum cross section would be conservative. In order to establish a method of evaluating strength reduction due to pitting corrosion, it is important to identify the failure mode that would be most detrimentally affected by pitting corrosion. It was found that the reduction of the ultimate compressive load or bending moment due to pitting corrosion is smaller than that of the tensile strength in terms of equivalent thickness.     

基于剪流分布规律的节点力加载方式在船体结构有限元分析中的应用

船体结构强度评估是船舶建造与设计过程中的重要环节.本文在总结研究现有的船体结构有限元分析加载方式的基础上,提出基于剪流分布规律的节点力加载方式.对于为模拟船体梁载荷而在各剖面处施加的集中力以及为进行强度计算需在各剖面处施加的调整载荷,使用本文方法将其离散至单元网格节点处并于与加载,得到的结果符合船体梁弯曲时的应力分布规律,这对于正确进行船体结构强度评估具有重要意义.给出适用于计算机实施的规格化加载过程,以实现船体结构有限元分析的自动加载过程.