粘弹性人工边界在地下结构抗震分析中的应用

地下结构地震反应分析需考虑结构-地基的动力相互作用,其中场地土层的自由场反应分析是确定地震输入的关键问题。以往地下工程实例表明,在结构动力时程计算中,能否有效模拟无限地基边界对结构抗震分析有很大的影响。基于某地下综合体项目进行抗震评估,采用黏弹性人工边界模拟自由场震动响应,克服工程中传统分析里不能模拟场地无限域的缺点。为地下结构的动力时程分析提供可靠数值依据。     

Influence of initial heeling angle on ship roll motion response北大核心CSCD

[目的]系统地研究初始横倾角对随机横浪下船舶横摇运动响应的影响。[方法]以路径积分法为基础,通过数值求解控制横摇运动微分方程概率属性的Fokker-Planck方程,得到横摇运动响应的概率分布。[结果]结果显示,初始横倾角对船舶横摇运动响应谱的影响有限,但对横摇角概率分布以及横摇运动响应极值分布的影响十分明显,且会造成船舶安全性的显著恶化。[结论]路径积分法可作为研究随机海浪下船舶横摇运动特性的有效数值方法。     

基于瞬态法的行李箱盖动态干涉研究

行车过程中行李箱盖在路面激励载荷作用下发生振动,当振动量超过行李箱盖和车身分缝间距时,就会发生干涉,导致漆膜破裂。文章利用有限元方法对汽车行李箱盖进行瞬态响应分析,并对其进行优化,最终经过台架试验和道路试验验证方案有效。为行李箱盖总成设计开发提供理论依据,并完善行李箱盖设计规范。     

列车动力响应的平稳性和各态历经性分析

研究列车动力响应的平稳性和各态历经性对寻求列车动力响应随机过程的统计规律具有重要意义。基于多体动力学理论,采用多体动力学分析软件Simpack建立国内某高速列车动车车辆的多体动力学模型。采用三角级数法模拟得到的轨道不平顺作为随机输入激励计算得到列车以不同速度行驶不同距离的动力响应时程样本序列。进一步运用平稳性检验方法中的逆序数检验法和单位根检验法对列车动力响应随机过程的平稳性进行检验。运用Monte-Carlo方法并结合随机过程的相关理论,计算1 500个在随机轨道不平顺激励下列车以200 km/h速度行驶1 km工况的动力响应时程样本序列的集合均值和集合相关函数,时间均值和时间相关函数,对列车动力响应的平稳性和各态历经性进行了证明。研究结果表明,列车以200 km/h的速度行驶1 km工况的动力响应可近似为具有各态历经性的平稳随机过程,即可采用一个时程响应样本来反映列车动力响应总体的统计规律。随着列车动力响应样本个数的增加,列车动力响应的平稳性和各态历经性都将更加稳定。     

带缆水下机器人控制仿真模拟与水动力分析

本文以Fluent多重滑移网格技术对带缆水下机器人系统进行路径跟踪的仿真计算,将收放缆反馈控制与PID算法调节螺旋桨转速的双重控制策略应用于带缆水下机器人系统,并对带缆水下机器人系统升沉运动的控制误差、螺旋桨推力与转速之间的关系、缆绳系统的张力特性以及水下机器人的水动力响应做了分析。文中数值模拟结果表明,双重控制策略下,带缆水下机器人路径跟踪的控制运动较为精确,其升沉运动位移最大误差约为0.2 m;螺旋桨的转速与推力呈正相关性,转速越大,推力也越大;水下机器人沿预定轨迹运动过程中,缆绳系统张力呈现周期性震荡的变化规律,机器人主体受到的水动力荷载与多种因素相关。     

Experimental study of freak wave impacts on a tension-leg platform

This study investigates the freak wave impinging on a tension-leg platform through wave flume experiments. The freak waves are generated using the focused wave theory. By adjusting the wave focusing location, different incident wave scenarios at the structure location are produced. Simultaneous measurements of wave shape evolutions upon impingement, wave impact pressures on the platform deck, platform motions and tether forces are carried out for synchronized analyses of the wave kinematics/dynamics and structural responses. The variation of these parameters with the incident wave profile is studied. It is found that although applying less intensive local impact pressures as compared to the highly-breaking freak wave, the slightly-breaking or non-breaking freak wave imposes the same level of adverse effect on the platform's global stability in terms of motions and tether forces. In addition, the high-crest freak wave causes violent motions of the floating platform, which are likely to induce snap loads of large amplitude and high occurrence frequency in tethers. The published results would provide useful benchmarks for validating numerical and analytical models.     

考虑流场影响下破冰船艏部结构响应研究

通常考虑船-冰碰撞附连水的水动力效应有附加质量法和流固耦合法。本文建立了破冰船破冰场景,基于流固耦合法进行了数值仿真计算,分析了水域流场对船体的冲击压力变化、流场的速度分布变化以及流场的动能变化。同时与附加质量法的计算结果进行了比较,对比分析了船艏的碰撞力大小、损伤变形以及局部冰载荷等差异,揭示了流场对船-冰碰撞的影响规律,对于破冰船结构设计具有重要的参考价值。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

Bend stiffener linear viscoelastic thermo-mechanical analysis. Part I — Experimental characterization and mathematical formulation

Bend stiffeners are subjected to cyclic loading during offshore operation or when subjected to a controlled full-scale qualification test. Due to the viscoelastic nature of the polyurethane, energy is dissipated within the material volume and the structure may experience a temperature increase, a phenomenon known as self-heating. The top connection is a flexible riser critical region in terms of fatigue, being the bend stiffener the main responsible for curvature control. As the curvature distribution is highly affected by the nonlinear time–temperature bend stiffener response, a detailed thermo-mechanical assessment may become relevant for riser lifetime and polyurethane material failure assessment, specially during accelerated full-scale tests. In the present paper (Part I), the polyurethane experimental characterization and steady-state thermo-mechanical mathematical formulation are presented for the bend stiffener self-heating assessment. A steady-state formulation is derived for a temperature dependent linear viscoelastic large deflection beam model to estimate the heat generation during harmonic tip loading. The temperature field distribution is calculated through a three-dimensional steady-state thermal model considering the viscoelastic heat calculated from the mechanical model with an iterative scheme. Stress relaxation tests are performed at different temperatures to determine the viscoelastic properties followed by thermal properties characterization through differential scanning calorimetry and by the Flash method to determine the specific heat, thermal conductivity and diffusivity, respectively. In a companion paper (Part II) the iterative numerical scheme is detailed and a case study presented.