Experimental Investigation of the Effect of Bow Profiles on Resistance of an Underwater Vehicle in Free Surface Motion

In this paper, towing tank experiments are conducted to study the behavior of flow on a model of the underwater vehicle with various shapes of bows, i.e. tango and standard bows in free surface motion ...     

Optimization of bow shape for a non ballast water ship

In this research,a commercial CFD code ＂Fluent＂ was applied to optimization of bulbous bow shape for a non ballast water ships（NBS）.The ship was developed at the Laboratory of the authors in Osaka Prefecture University,Japan.At first,accuracy of the CFD code was validated by comparing the CFD results with experimental results at towing tank of Osaka Prefecture University.In the optimizing process,the resistances acting on ships in calm water and in regular head waves were defined as the object function.Following features of bulbous bow shapes were considered as design parameters： volume of bulbous bow,height of its volume center,angle of bow bottom,and length of bulbous bow.When referring to the computed results given by the CFD like resistance,pressure and wave pattern made by ships in calm water and in waves,an optimal bow shape for ships was discovered by comparing the results in the series of bow shapes.In the computation on waves,the ship is in fully captured condition because shorter waves,λ/Lpp 0.6,are assumed.     

液舱晃荡与浮体非线性耦合运动分析(英文)

Nonlinear interactions among incident wave, tank-sloshing and floating body coupling motion are investigated. The fully nonlinear sloshing and body-surface nonlinear free surface hydrodynamics is simulated using a Non-Uniform Rational B-Spline (NURBS) higher-order panel method in time domain based on the potential theory. A robust and stable improved iterative procedure (Yan and Ma, 2007) for floating bodies is used for calculating the time derivative of velocity potential and floating body motion. An energy dissipation condition based on linear theory adopted by Huang (2011) is developed to consider flow viscosity effects of sloshing flow in nonlinear model. A two-dimensional tank model test was performed to identify its validity. The present nonlinear coupling sway motion results are subsequently compared with the corresponding Rognebakke and Faltinsen (2003)’s experimental results, showing fair agreement. Thus, the numerical approach presented in this paper is expected to be very efficient and realistic in evaluating the coupling effects of nonlinear sloshing and body motion.     

Resistance analysis of unsymmetrical trimaran model with outboard sidehulls configuration

The application of multi-hull ship or trimaran vessel as a mode of transports in both river and sea environments have grown rapidly in recent years.Trimaran vessels are currently of interest for many new high speed ship projects due to the high levels of hydrodynamic efficiency that can be achieved,compared to the mono-hull and catamaran hull forms.The purpose of this study is to identify the possible effects of using an unsymmetrical trimaran ship model with configuration（S/L） 0.1-0.3 and R/L=0.1-0.2.Unsymmetrical trimaran ship model with main dimensions： L=2000mm,B=200 mm and T=45 mm.Experimental methods（towing tank） were performed in the study using speed variations at Froude number 0.1-0.6.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was measured precisely by using a load cell transducer.The comparison of ship resistance for each configuration with mono-hull was shown on the graph as a function of the total resistance coefficient and Froude number.The test results found that the effective drag reduction could be achieved up to 17% at Fr=0.35 with configuration S/L=0.1.     

船体周围Stokes波浪流耦合VOF模型的数值模拟（英文）

The surface wave generated by flow around a ship hull moving near free surface of water is simulated numerically in this study. The three-dimensional implicit finite volume method(FVM) is applied to solve Reynolds averaged Navier-Stokes(RANS) equation. The realizable k-ε turbulence model has been implemented to capture turbulent flow around the ship hull in the free surface zone. The volume of fluid(VOF) method coupled with the Stokes wave theory has been used to determine the free surface effect of water. By using is a six degrees of freedom model, the ship hull's movement is numerically solved with the Stokes wave together. Under the action of Stokes waves on the sea, the interface between the air and water waves at the same regular pattern and so does the pressure and the vertical velocity. The ship hull moves in the same way as the wave. The amplitude of the ship hull's heave is less than the wave height because of the viscosity damping. This method could provide an important reference for the study of ships' movement, wave and hydrodynamics.     

由多孔介质注射的微气泡和气层对减小自航驳船模型拖曳力效果的比较研究（英文）

Ship resistance issues are related to fuel economy, speed, and cost efficiency. Air lubrication is a promising technique for lowering hull frictional resistance as it is supposed to modify the energy in the turbulent boundary layer and thereby reduce hull friction. In this paper, the objective is to identify the optimum type of air lubrication using microbubble drag reduction(MBDR)and air layer drag reduction(ALDR) techniques to reduce the resistance of a 56-m Indonesian self-propelled barge(SPB). A model with the following dimensions was constructed: length L = 2000 mm, breadth B = 521.60 mm, and draft T = 52.50 mm.The ship model was towed using standard towing tank experimental parameters. The speed was varied over the Froude number range 0.11–0.31. The air layer flow rate was varied at 80, 85, and 90 standard liters per minute(SLPM) and the microbubble injection coefficient over the range 0.20–0.60. The results show that the ship model using the air layer had the highest drag reduction up to a maximum of 90%. Based on the characteristics of the SPB, which operates at low speed, the optimum air lubrication type to reduce resistance in this instance is ALDR.     

流线型潜体首型对纵倾斜流涡结构的影响数值模拟（英文）

A flow field around a streamlined body at an intermediate angle of incidence is dominated by cross-flow separation and vortical flow fields. The separated flow leads to a pair of vortices on the leeside of the body; therefore, it is essential to accurately determine this pair and estimate its size and location. This study utilizes the element-based finite volume method based on RANS equations to compute a 3D axisymmetric flow around a SUBOFF bare submarined hull. Cross-flow vortex structures are then numerically simulated and compared for a submarine with SUBOFF and DRDC STR bows. Computed results of pressure and shear stress distribution on the hull surface and the strength and locations of the vortex structures are presented at an intermediate incidence angle of 20°. A wind tunnel experiment is also conducted to experimentally visualize the vortex structures and measure their core locations. These experimental results are compared with the numerical data, and a good agreement is found.     

Dynamic interaction of parallel moving ships in close proximity

Nowadays,there are many studies conducted in the field of marine hydrodynamics which focus on two vessels traveling and floating in sufficiently close proximity to experience significant interactions.The hydrodynamic behavior of parallel moving ships in waves is an interesting and important topic of late.A numerical investigation has been carried out for the prediction of wave exciting forces and motion responses of parallel moving ships in regular waves.The numerical solution was based on 3D distribution technique and using the linear wave theory to determine the exciting forces and ship＇s motion.The speed effects have been considered in the Green function for more realistic results.The numerical computations of wave exciting forces and motion responses were carried out for a Mariner and Series 60 for the purpose of discovering different Froude numbers and different separation distances in head sea conditions.Based on the numerical computations,it was revealed that the sway,roll and yaw have a significant effect due to hydrodynamic interaction.     

Added resistance acting on hull of a non ballast water ship

In this paper, added resistances acting on a hull of non ballast water ship(NBS) in high waves is discussed. The non ballast water ships were developed at the laboratory of the authors at Osaka Prefecture University, Japan. In the present paper, the performances of three kinds of bow shapes developed for the NBS were theoretically and experimentally investigated to find the best one in high waves. In previous papers, an optimum bow shape for the NBS was developed in calm water and in moderated waves. For a 2 m model for experiments and computations, the wave height is 0.02 m. This means that the wave height is 15% of the draft of the ship in full load conditions. In this paper, added resistances in high waves up to 0.07 m for a 2 m model or 53% of the full load draft are investigated. In such high waves linear wave theories which have been used in the design stage of a ship for a long time may not work well anymore, and experiments are the only effective tool to predict the added resistance in high waves. With the computations for waves, the ship is in a fully captured condition because shorter waves, λ/Lpp0.6, are assumed.     

Numerical Simulation of the Stokes Wave for the Flow around a Ship Hull Coupled with the VOF Model

The surface wave generated by flow around a ship hull moving near free surface of water is simulated numerically in this study. The three-dimensional implicit finite volume method(FVM) is applied to solve Reynolds averaged Navier-Stokes(RANS) equation. The realizable k-ε turbulence model has been implemented to capture turbulent flow around the ship hull in the free surface zone. The volume of fluid(VOF) method coupled with the Stokes wave theory has been used to determine the free surface effect of water. By using is a six degrees of freedom model, the ship hull’s movement is numerically solved with the Stokes wave together. Under the action of Stokes waves on the sea, the interface between the air and water waves at the same regular pattern and so does the pressure and the vertical velocity. The ship hull moves in the same way as the wave. The amplitude of the ship hull’s heave is less than the wave height because of the viscosity damping. This method could provide an important reference for the study of ships’ movement, wave and hydrodynamics.     

A free surface frequency domain green function with viscous dissipation and partial reflections from side walls

The free-surface Green function method is widely used in solving the radiation or diffraction problems caused by a ship or ocean structure oscillating on the waves. In the context of inviscid potential flow, hydrodynamic problems such as multi-body interaction and tank side wall effect cannot be properly dealt with based on the traditional free-surface frequency domain Green function method, in which the water viscosity is omitted and the energy dissipation effect is absent. In this paper, an open-sea Green function with viscous dissipation was presented within the theory of visco-potential flow. Then the tank Green function with a partial reflection from the side walls in wave tanks was formulated as a formal sum of open-sea Green functions representing the infinite images between two parallel side walls of the source in the tank. The new far-field characteristics of the tank Green function is vitally important for improving the validity of side-wall effects evaluation, which can be used in supervising the tank model tests.     

Determining the hydrodynamic forces on a planing hull in steady motion

A combination of methods was developed that can determine hydrodynamic forces on a planing hull in steady motion. Firstly, a potential-based boundary-element method was used to calculate the hydrodynamic pressure, induced resistance and lift. Then the frictional resistance component was determined by the viscous boundary layer theory. Finally, a particular empirical technique was applied, to determine the region of upwash geometry and determine spray resistance. Case studies involving four models of Series 62 planing craft were run. These showed that the suggested method is efficient and capable, with results that are in good agreement with experimental measurements over a wide range of volumetric Froude numbers.     

Determining the hydrodynamic forces on a planing hull in steady motion

A combination of methods was developed that can determine hydrodynamic forces on a planing hull in steady motion.Firstly,a potential-based boundary-element method was used to calculate the hydrodynamic pressure,induced resistance and lift.Then the frictional resistance component was determined by the viscous boundary layer theory.Finally,a particular empirical technique was applied.to determine the region of upwash geometry and determine spray resistance.Case studies involving four models of Series 62 planing craft were run.These showed that the suggested method is efficient and capable,with results that are in good agreement with experimental measurements over a wide range of volumetric Froude numbers.     

海水风机与不同类型基座耦合的非稳态流动分析（英文）

Environmental effects have an important influence on Offshore Wind Turbine(OWT) power generation efficiency and the structural stability of such turbines. In this study, we use an in-house Boundary Element(BEM)—pan MARE code—to simulate the unsteady flow behavior of a full OWT with various combinations of aerodynamic and hydrodynamic loads in the time domain. This code is implemented to simulate potential flows for different applications and is based on a three-dimensional first-order panel method. Three different OWT configurations consisting of a generic 5 MW NREL rotor with three different types of foundations(Monopile, Tripod, and Jacket) are investigated. These three configurations are analyzed using the RANSE solver which is carried out using ANSYS CFX for validating the corresponding results. The simulations are performed under the same environmental atmospheric wind shear and rotor angular velocity, and the wave properties are wave height of 4 m and wave period of 7.16 s. In the present work, wave environmental effects were investigated firstly for the two solvers, and good agreement is achieved. Moreover, pressure distribution in each OWT case is presented, including detailed information about local flow fields. The time history of the forces at inflow direction and its moments around the mudline at each OWT part are presented in a dimensionless form with respect to the mean value of the last three loads and the moment amplitudes obtained from the BEM code, where the contribution of rotor force is lower in the tripod case and higher in the jacket case and the calculated hydrodynamic load that effect on jacket foundation type is lower than other two cases.     

二维冲箱式造波机的间隙和形状效应数值研究（英文）

The installation of plunger-type wave makers in experimental tanks will generally include a gap between the back of the wedge and the wall of the tank. In this study, we analyze the influence of this gap on the wave making performance of the plunger using two-dimensional(2 D) CFD calculations for a range of nearly linear wave conditions and compare the results with both experimental measurements and linear potential flow theory. Three wedge-shaped profiles, all with the same submerged volume, are considered. Moreover, the generated waves are compared with the predictions of linear potential flow theory. The calculations are made using the commercial ANSYS FLUENT finite-volume code with dynamic meshes to solve the Navier–Stokes equations and the volume of fluid scheme to capture the air–water interface. Furthermore, the linear potential flow solution of Wu(J Hydraul Res 26:481–493, 1988) is extended to consider an arbitrary profile and serve as a reference solution. The amplitude ratios of the generated waves predicted by the CFD calculations compare well with the predictions of linear potential flow theory for a simple wedge, indicating that viscous effects do not influence this ratio for small-amplitude motions in 2 D. By contrast,significant higher harmonic components are produced by larger amplitude motions. Also, the simple wedge is found to produce the smallest spurious higher harmonic content in the far-field wave.     

采用微气泡缩减高速船拖曳阻力(英文)

Ship hull form of the underwater area strongly influences the resistance of the ship.The major factor in ship resistance is skin friction resistance.Bulbous bows,polymer paint,water repellent paint(highly water-repellent wall),air injection,and specific roughness have been used by researchers as an attempt to obtain the resistance reduction and operation efficiency of ships.Micro-bubble injection is a promising technique for lowering frictional resistance.The injected air bubbles are supposed to somehow modify the energy inside the turbulent boundary layer and thereby lower the skin friction.The purpose of this study was to identify the effect of injected micro bubbles on a navy fast patrol boat(FPB) 57 m type model with the following main dimensions:L=2 450 mm,B=400 mm,and T=190 mm.The influence of the location of micro bubble injection and bubble velocity was also investigated.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was precisely measured by a load cell transducer.Comparison of ship resistance with and without micro-bubble injection was shown on a graph as a function of the drag coefficient and Froude number.It was shown that micro bubble injection behind the mid-ship is the best location to achieve the most effective drag reduction,and the drag reduction caused by the micro-bubbles can reach 6%-9%.     

Optimization of Wigley Hull Form in order to Ensure the Objective Functions of the Seakeeping Performance

The research performed in this paper was carried out to investigate the computational procedure to design seakeeping optimized ship hull form. To reach the optimized hull form, four stages should be done, which consists of： generate alternative hull form, seakeeping calculations, objective functions and optimization techniques. There are many parameters that may be determined in ship hull form optimization. This paper deals with developed strip theory for determining the seakeeping performance, genetic algorithm （GA） as optimization method, high order equations for curve fitting of the hull form and finally reaching to the minimum bow vertical motion in regular head waves. The Wigley hull is selected as an initial hull and carried to be optimized. Two cases are considered. For the first case, the only form coefficients of the hull （CB, CM, Cw, Cp） are changed and main dimensions （L, B, 7） are fixed. In the second case both hull form and main dimensions are varied simultaneously. Finally, optimized hull form and its seakeeping performances are presented. The results of optimization procedure demonstrate that the optimized hull forms yield a reduction in vertical motion and acceleration.     

The research on signal-obtaining pattern for a new type of gyroscope

In this paper, a photoelectric signal obtained scheme via equator triangle pattern engraved on rotor is discussed and the mathematic model is deduced in the case which is deflexion between rotor axis and the coordinate frame of case. The deflexion error and coupling error under the situation are analyzed. Finally, three methods of engraving based on the spherical triangle pattern are presented. The error models of various methods are built up and the simulation curves are provided respectively. We have done the primary experiments on the surface of rotor using this method. It can be seen from the enlarged figures that the rim of the pattern is smooth and the demand of sensor resolution is satisfied by and large. The results of study supply reference for signal obtaining.     

五体船非对称侧体的干扰阻力（英文）

An experimental investigation is performed to assess the relation of interference performance on the total resistance of a pentamaran model advancing in calm water. For this motivation, the total drag of the ship is performed for several values of asymmetric outrigger configuration and hull separation, altering the Froude number in the range 0.3–0.9. Our results indicate that remarkable changes in resistance require notable changes in transverse distance values(hull separation) when wave interference may occur. In addition, there is no single configuration that consistently outperforms the other configurations across the entire speed range and the optimum interference factor-0.2 appears at a Froude number of 0.45 in S/L=0.33 with the outrigger outer position: asymmetric outboard for A3 configuration.     

The method of imbedded Lagrangian element to estimate wave power absorption by some submerged devices

A simple approach is described to estimate the wave power absorption potential of submerged devices known to cause wave focusing and flow enhancement. In particular, the presence of a flow-through power take-off （PTO） system, such as low-head turbines, can be accounted for. The wave radiation characteristics of an appropriately selected Lagrangian element （LE） in the fluid domain are first determined. In the limit of a vanishing mass, the LE reduces to a patch of distributed normal dipoles. The hydrodynamic coefficients of this virtual object are then input in a standard equation of motion where the effect of the PTO can be represented, for example, as a dashpot damping term. The process is illustrated for a class of devices recently proposed by Carter and Ertekin （2011）, although in a simplified form. Favorable wave power absorption is shown for large ratios of the LE wave radiation coefficient over the LE added mass coefficient. Under optimal conditions, the relative flow reduction from the PTO theoretically lies between 0.50 and 1 2 ≈ 0.71, with lower values corresponding to better configurations. Wave power capture widths, the sensitivity of results to PTO damping and sample spectral calculations at a typical site in Hawaiian waters are proposed to further illustrate the versatility of the method.