柴油机微粒捕集器催化再生技术

柴油机微粒捕集器（DPF）能降低柴油机的微粒（PM）排放量,文章提出了DPF催化再生技术方案,将氧化催化器（DOC）与DPF相结合,通过DOC催化氧化未燃HC等来提高排气温度达到微粒着火温度500～600℃,点燃微粒从而完成再生过程。以YN4100QB–1A柴油机为研究对象,对不同喷油量下的DPF升温特性进行了试验研究,试验结果表明：当喷油量大于60mL/min时,再生系统能迅速将排气温度提高到500℃以上。可变喷油量的喷油控制方案可使DPF升温平缓,降低再生造成的二次污染。     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.     

柴油机微粒捕集器定工况主动再生条件的试验研究

柴油机尾气后处理系统采用仅安装氧化催化转化器方案,通过试验确定了柴油机微粒捕集器定工况主动再生时所需的入口条件,通过对发动机不同工况排气温度的测量确定了微粒捕集器定工况主动再生的发动机工况点,得出了主动再生时排气管中所需喷入液化石油气的喷射脉宽.试验中氧化催化转化器对HC的转化效率达到了90%以上,满足了再生期间对催化...     

Carbon Deposit Incineration During Engine Flameout Using Non-Thermal Plasma Injection

In order to investigate the influence of initial regeneration temperatures on diesel particulate filter (DPF) regeneration, an experimental study of DPF regeneration was implemented using a dielectric barrier discharge (DBD) reactor, aided by exhaust waste heat after engine flameout. DPF trapping characteristics and carbon deposit mass were discussed to facilitate further data analysis and calculation. DPF regeneration was then investigated by comparison analysis of deposit removal mass, backpressure drop, and internal temperature change. The results revealed that a large amount of particulate matter (PM) was deposited in DPF with a high filtration efficiency of about 90 %. The deposit removal rate and percentage drop of the backpressure both maximized at the initial temperature of 100 °C. During DPF regeneration, the sharp rise of internal temperature indicated vigorous PM incineration and high CO₂ emission. The results successfully demonstrated DPF regeneration using non-thermal plasma injection during engine flameout, and prominent heat durability was achieved in this method.     

Estimation of soot oxidation rate in DPF under carbon and non-carbon based particulate matter accumulated condition

By high particulate matter(PM) reduction performance, diesel particulate filter(DPF) is applied to almost all of modern HSDI diesel engine. PM emitted from diesel engine is consist of carbon based and non-carbon based material. Representative carbon based PM is soot. Non-carbon based PM is produced by wear of engine and exhaust component, combustion of lubrication oil and sulphur in fuel. Accumulation of non-carbon based PM affects pressure difference of DPF and thus accuracy of soot mass estimation in DPF can be lowered during normal and regeneration condition when the pressure difference caused by non-carbon based PM is not recognized correctly. Also unevenly accumulated PM inside of DPF can produce locally different exhaust gas temperature and thus it can lower accuracy of soot mass estimation during regeneration. This study focuses on estimation of soot oxidation rate not by conventional pressure difference but by exhaust gas analysis at up and downstream of DPF. Results, strong correlations between CO₂ -fuel mass ratio and soot oxidation was observed.     

加载减速工况下带有DPF柴油车的颗粒物排放

基于加载减速工况,利用ELPI能够有效研究颗粒物排放状况以及其数目浓度和质量浓度在粒径上的分布,研究证实,这种测试技术具有很高的DPF性能鉴别能力。通过量化分析颗粒物在DPF前后粒径上的浓度分布以及图解DPF前后的浓度差值,可以非常清晰地发现该DPF对于不同粒径的过滤性能,为开发和匹配柴油车颗粒物过滤器提供一种有效的手段。     

Morphology and oxidation kinetics of CI engine’s biodiesel particulate matters on cordierite Diesel Particulate Filters using TGA

The impact of small compression ignition (CI) engine operation conditions and fuel properties on diesel and biodiesel particulate matters (PMs) quantity using opacity smoke meter is investigated. The biodiesel engine’s PMs are around a half of diesel engine PMs under the same engine operation conditions. Morphology of both engine’s PMs are also studied using a Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and image processing method. The average primary nanoparticle sizes of diesel and biodiesel engine’s PMs are approximately 34 nm and 32 nm, respectively. The result shows that engine operation condition and fuel property are strongly impact on the quantity and size distribution of primary nanoparticles emission. PM oxidation kinetics on conventional cordierite Diesel Particulate Filters (DPFs) powders by Thermo-gravimetric analysis (TGA) is also successfully studied. The calculated apparent activation energies of biodiesel engine’s PM oxidation on conventional cordierite DPFs powders are lower than that of diesel engine’s PM and carbon black because of unburned oxygenated molecule. The calculated apparent activation energy of biodiesel engine’s PM and diesel engine’s PM oxidize on conventional cordierite DPFs powders with pure air are in the range of 109 ~ 131 kJ/mole and 117 ~ 130 kJ/mole, respectively. It might be expected that smaller primary nanoparticle size of biodiesel engine’s PMs and bio-oxygenate unburned hydrocarbon can promote more PM oxidation rate during vehicle’s DPF regeneration process.     

DOC+DPF对柴油机颗粒物排放特性的影响研究

以某型高压共轨柴油机为研究对象,研究试验样机加装DOC+DPF后处理装置对其颗粒排放特性的影响。结果表明:试验样机连接DOC+DPF后,颗粒物排放显著降低,在中高转速下,转化率平均在97%以上;在中低转速DOC+DPF对积聚态颗粒净化效率高于核模态颗粒,在1030rpm下,颗粒物总数量下降89%,总质量下降33%;在1200rpm下,颗粒物总数量下降96%,总质量下降77%。在1030rpm和1600rpm除了70%负荷外,DOC+DPF前的NO2/NOX比值都高于DOC+DPF后的,DOC+DPF后的NO2/NOX比值随负荷增加先减小后增加。     

基于机器学习的柴油机碳烟颗粒质量排放预测模型

基于SC7H涡轮增压柴油机试验台架,开展了非道路瞬态试验循环下的柴油机排放试验,研究了瞬态循环的工况对碳烟颗粒质量浓度的影响。收集与碳烟颗粒质量浓度相关的各类传感器数据,构建一个大型的柴油机碳烟排放数据集。构建LGB梯度树模型和循环神经网络模型,采用数据集对它们进行训练,然后采用自学习算法对两种模型进行融合,获得一个更高准确度的预测碳烟质量排放融合模型。预测与实测结果的比较表明,构建的融合模型能较为准确地预测柴油机排放的即DPF入口的碳烟质量浓度实时变化,为柴油机后处理过程中碳载量的准确计算以及控制策略的开发提供参考。     

柴油机排气颗粒物捕集器的发展

柴油机在轻型车辆上使用的日趋普遍,使得柴油机排放气体中的颗粒物后处理成为研究热点。颗粒物捕集器是解决柴油机排气颗粒污染最有效的后处理技术。针对目前国内颗粒物捕集器的使用情况,论述了柴油机排气颗粒物捕集器过滤材料和过滤体再生技术近年来的研究现状,介绍了近年来过滤材料和过滤体再生技术结合良好的几种颗粒物捕集器,提出了颗粒物捕集器今后的研究方向。     

Experimental study on the characteristics of nano-particle emissions from a heavy-duty diesel engine using a urea-SCR system

Particulate matter in diesel engine exhaust, particularly nano-particles, can cause serious human health problems including diseases such as lung cancer. Because diesel nano-particle issues are of global concern, regulations on particulate matter emissions specify that not only the weight of particulate matter emitted but also the concentration of nanoparticles must be controlled. This study aimed to determine the effects on nano-particle and PM emissions from a diesel engine when applying a urea-SCR system for NO_x reduction. We found that PM weight increases by approximately 90% when urea is injected in ND-13 mode over the emission without urea injection. Additionally, PM weight increases as the NH₃/NO_x mole ratio is increased at 250 °C. In SEM scans of the collected PM, spherical particles were observed during urea injection, with sizes of approximately 200 nm to 1 μm. This study was designed to determine the conditions under which nano-particles and PM are formed in a urea-SCR system and to relate these conditions to particle size and shape via a quantitative analysis in ND-13 mode.     

Heat exchanger/catalytic system for reducing the exhaust emissions from diesel engines

A system has been researched over the past 3 years for reducing the exhaust pollutants from diesel engines for light commercial vehicles. The system researched achieves Euro 6 standards for reduction of polluting gases (CO, HC, PM, NO). It consists of 4 main sections: 1. A heater and heat exchanger (HE); 2. A CO/HC oxidising catalyst (D°C); 3. Pt catalyst on a diesel particulate filter (DPF); 4. A NO reducing reaction (SCR) within the DPF. The system operates as follows. The exhaust gas contains oxidising gases, namely both O₂ and NO₂. The levels of CO and HC are oxidised by O₂ to CO₂ for temperatures above 200°C. Carbon (PM) is oxidised to CO₂ by NO₂ but requires a temperature above 250°C. The operating exhaust temperature of 300°C is ideal for the removal of NO by using the Pt catalyst and the CO generated within the DPF. The heater is required to be able to raise the exhaust temperature at any time to 300°C in order to optimise the performance of the system, since diesel engine exhaust temperatures vary between 160°C (slow speeds) to 350°C (high speeds). Considerable heat is required (??3 kW) to maintain the exhaust gas for a 2l engine at 300°C for engine idle conditions. Therefore a heat exchanger is required to re-circulate the input heat and thereby reduce the maximum power consumption to a maximum of 500W over the engine full operating test cycle. This energy is supplied by the engine battery and alternator. Experimental results have been obtained for the exhaust from a Kubota diesel engine and the reductions in exhaust emissions of 83% (CO/ HC), 58% (NOx) and 99% (PM) were obtained. The PM was continuously cleaned so that there was no build up of back pressure.     

Nano-particle emission characteristics of European and Worldwide Harmonized test cycles for heavy-duty diesel engines

This study was conducted for the experimental comparison of particulate emission characteristics between the European and World-Harmonized test cycles for a heavy-duty diesel engine as part of the UN/ECE PMP ILCE of the Korea Particulate Measurement Program. To verify the particulate mass and particle number concentrations from various operating modes, ETC/ESC and WHTC/WHSC, were evaluated. Both will be enacted in Euro VI emission legislation. The real-time particle emissions from a Mercedes OM501 heavy-duty golden engine with a catalyst based uncoated golden DPF were measured with CPC and DMS during daily test protocol. Real-time particle formation of the transient cycles ETC and WHTC were strongly correlated with engine operating conditions and after-treatment device temperature. The higher particle number concentration during the ESC #7 to #10 mode was ascribed to passive DPF regeneration and the thermal release of low volatile particles at high exhaust temperature conditions. The detailed average particle number concentration equipped for golden DPF reached approximately 4.783E+11 #/kWh (weighted WHTC), 6.087E+10 #/kWh (WHSC), 4.596E+10 #/kWh (ETC), and 3.389E+12 #/kWh (ESC). Particle masses ranged from 0.0011 g/kWh (WHSC) to 0.0031 g/kWh (ESC). The particle number concentration and mass reduction of DPF reached about 99%, except for an ESC with a reduction of 95%.     

Comparison of fuel efficiency and exhaust emissions between the aged and new DPF systems of Euro 5 diesel passenger car

This study was conducted to examine the impact of aged and new DPF systems of the Euro 5 diesel passenger car on fuel efficiency and exhaust emissions. Test diesel vehicle used in this study was equipped with diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) as aftertreatment systems, and satisfied the Euro-5 emissions standard. The displacement volume of engine was 1.6 L and the cumulative mileage was 167,068 km before the test. The FTP-75 test procedure was used, and the time resolved and weight based exhaust emissions of total hydrocarbon (THC), carbon monoxide (CO) and nitrogen oxides (NOx) were measured. The results show that the vehicle with the new DPF system has lower emissions of THC, CO and NOx than the aged one, and fuel efficiency also increased about 5 percent. The aged DPF system had higher backpressure due to the particulate matter (mostly in the form of ash) accumulated in the DPF. As was shown in the analysis using X-CT (X-ray computer tomography), the aged DPF system had particulate matter (PM) accumulated to a length of 46.6 mm. In addition, a component analysis of PM through XRF (X-ray fluorescence) analysis found that 50 % or more of the components consisted of the P, S, Ca, and Zn.     

Effect of operating parameters on diesel/propane dual fuel premixed compression ignition in a diesel engine

In this research, the effects of three operating parameters (Diesel injection timing, propane ratio, and exhaust gas recirculation (EGR) rates) in a diesel-propane dual fuel combustion were investigated. The characteristics of dual-fuel combustion were analyzed by engine parameters, such as emission levels (Nitrogen oxides (NO_x) and particulate matter (PM)), gross indicated thermal efficiency (GIE) and gross IMEP Coefficient of Variance (CoV). Based on the results, improving operating strategies of the four main operating points were conducted for dual-fuel PCCI combustion with restrictions on the emissions and the maximum pressure rise rate. The NOx emission was restricted to below 0.21 g/kWh in terms of the indicated specific NO_x (ISNO_x), PM was restricted to under 0.2 FSN, and the maximum pressure rise rate (MPRR) was restricted to 10 bar/deg. Dual-fuel PCI combustion can be available with low NO_x, PM emission and the maximum pressure rise rate in relatively low load condition. However, exceeding of PM and MPRR regulation was occurred in high load condition, therefore, design of optimal piston shape for early diesel injection and modification of hardware optimizing for dual-fuel combustion should be taken into consideration.     

Simulation of flow in diesel particulate filter system using metal fiber filter media

Metal fiber is introduced as a new filter media in wall-flow Diesel Particulate Filter (DPF) system. This technology has high temperature durability which is required for filter regeneration, and can maintain the mechanical strength even in the extreme exhaust-related vibrations of vehicles. However, the regeneration near the wall (outer layer) is more difficult because of the heat loss and reduced gas flow near the wall. In this study, a flow is simulated to determine the flow control method for the more uniform flow in all filter layer. By using Star CCM+ commercial software, we obtain local velocity, streamline, and pressure distributions in the filter, which are typically difficult to obtain from measurements. The major control factors are the filter porosity, size and location of the distribution plate, and the number of blades of the swirler. By placing the distribution plate in front of the filter, the flow velocity near the wall was increased. The optimum location and size of the flat plate were chosen. By attaching the blade on the plate the flow velocity near the wall was increased more. Therefore, the regeneration efficiency is increased by using the swirler-type metal fiber DPF system.     

Experimental investigation and comparison of nanoparticle emission characteristics in light-duty vehicles for two different fuels

In recent years, particle number emissions rather than particulate mass emissions in automotive engines have become the subject with controversial discussions. Recent results from studies of health effects imply that it is possible that particulate mass does not properly correlate with the variety of health effects attributed to engine exhaust. The concern is now focusing on nano-sized particles emitted from I. C. engines. In this study, particulate mass and particle number concentration emitted from light-duty vehicles were investigated for a better understanding of the characteristics of the engine PM from different types of fuels, such as gasoline and diesel fuel. Engine nano-particle mass and size distributions of four test vehicles were measured by a condensation particle counter system, which is recommended by the particle measurement program in Europe (PMP), at the end of a dilution tunnel along a NEDC test mode on a chassis dynamometer. We found that particle number concentrations of diesel passenger vehicles with DPF system are lower than gasoline passenger vehicles, but PM mass has some similar values. However, in diesel vehicles with DPF system, PM mass and particle number concentrations were greatly influenced by PM regeneration. Particle emissions in light-duty vehicles emitted about 90% at the ECE15 cycle in NEDC test mode, regardless of vehicle fuel type. Particle emissions at the early cold condition of engine were highly emitted in the test mode.     

可调涡轮增压器与柴油机匹配试验研究

对Ｊ６１１０Ｚ型柴油机匹配套式移动结构可调涡轮增压器进行了台架试验研究，试验中，在调节涡轮截面时没有进行相应的油量调节，而重点对柴油机各种工况下ＶＧＴ－７０型增压器的性能进行了研究分析。     

DPF对柴油车颗粒物排放的影响研究

利用ELPI（电子低压冲击器）对加载DPF的柴油车分别在DPF前后和未安装DPF时进行取样,能有效研究颗粒物排放状况以及颗粒物数量浓度和质量浓度在粒径上的分布。研究发现,安装DPF后将增加车辆发动机排放的颗粒物数量和质量,但经过DPF过滤后,颗粒物质量和数量都会大幅减少,过滤效果良好。     

Experimental Investigation of Impacts of Injection Timing and Pressure on Combustion and Particulate Matter Emission in a Spray-Guided GDI Engine

A detailed investigation of the impact of injection timing and injection pressure on combustion and particles of a spray-guided GDI engine was conducted, under different engine operating conditions. The results indicated that, more proportion of large particles were emitted when increasing engine load, and the peak of accumulation mode particles moved toward smaller size when rising engine speed. With retarding the injection timing, the in-cylinder pressure and heat release rate rose first and then dropped at 2000 rpm, but they continuously rose at lower or higher speed conditions. The total particles concentration curves at all cases showed a trend of U-shape, and the corresponding timing of the lowest particles concentration advanced as the engine speed or load increased. The minimum value of emitted particles first rose and then fell when increasing load at 2000 rpm conditions, and it continuously rose when increasing speed at 40 Nm conditions. Generally, injection pressure did no sensitively affect combustion process except that it showed a relatively strong impact at low load conditions. However, particulate matter could be effectively inhibited by elevating fuel pressure from 5.5 to 11.5 MPa at all cases. In detail, the total particles concentration continuously fell at low speed and mid speed-high load cases, but it showed a rose trend when further increase fuel injection pressure at mid speed-low load and high-speed conditions.