Real-world gaseous emission characteristics of Euro 6b light-duty gasoline- and diesel-fueled vehicles

To accurately investigate vehicle emissions that have become major contributors to global air pollutants and greenhouse gases, test conditions have been transferred from laboratory type approval test cycles to real-world driving conditions. In this study, the real-world driving emissions of carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NO_x), and carbon dioxide (CO₂) from one gasoline and two diesel Euro 6b light-duty passenger vehicles were investigated by a portable emission measurement system (PEMS) in Lyon, France. NO_x and CO₂ emission controls remain critical to addressing the real-world driving emissions of Euro 6b vehicles. Notably, the tested gasoline vehicle emitted higher CO₂ emissions than diesel vehicles on all types of roads, especially on the urban road with an excess of 29.3–48.3%. The highest emission factors of gaseous pollutants generally occurred on the motorway for the gasoline vehicle, while on the urban road for diesel vehicles. In particular, for high-speed driving conditions, the gasoline vehicle gaseous emissions, especially NO_x emissions, were more affected by acceleration than diesel vehicle emissions. In addition, the CO emissions, especially THC emissions, for the gasoline vehicle, were more influenced by warm-start, especially cold-start, than those for diesel vehicles.     

Costs of air pollutants from shipping: a meta-regression analysis

ABSTRACT

This study estimated the external cost of air pollution from shipping by means of a meta-regression analysis, which has not been made before. Three pollutants, which were included in most of the primary studies, were considered: nitrogen oxides (NO_x), sulphur dioxides (SO₂) and particulate matters with a diameter of max 2.5 micrometres (PM_2.5). All primary studies included damages of health and a majority added impacts on agriculture and estimated the cost of air pollutants by transferring cost estimates from studies on costs of air emissions from transports in Europe. Different regression models and estimators were used and robust results were found of statistically significant emission elasticities of below one, i.e. total external costs increase by less than 1% when emissions increase by 1%. There was a small variation between the pollutants, with the highest elasticity for PM_2.5 and lowest for NO_x. Calculations of the marginal external cost of the pollutants showed the same pattern, with this cost being approximately six times higher for PM_2.5 than for the other pollutants. Common to all pollutants was that the marginal external cost decreases when emission increases. Another robust result was a significant increase in the cost of studies published in journals compared with other publication outlets. These findings point out some caution when transferring constant external unit cost of air pollutant from shipping, which is much applied in the literature, and the cost functions estimated in this study could thus provide a complementary transfer mechanism.     

Reducing emissions at land border crossings through queue reduction and expedited security processing

Vehicle border crossings between Mexico and the United States generate significant amounts of air pollution, which can pose health threats to personnel at the ports of entry (POEs) as well as drivers, pedestrians, and local inhabitants. Although these health risks could be substantial, there is little previous work quantifying detailed emission profiles at POEs. Using the Mariposa POE in Nogales, Arizona as a case study, light-duty and heavy-duty vehicle emissions were analyzed with the objective of identifying effective emission reduction strategies such as inspection streamlining, physical infrastructure improvements, and fuel switching. Historical traffic information as well as field data were used to establish a simulation model of vehicle movement in VISSIM. Four simulation scenarios with varied congestion levels were considered to represent real-world seasonal changes in traffic volume. Four additional simulations captured varying levels of expedited processing procedures. The VISSIM output was analyzed using the EPA’s MOVES emission simulation software for conventional air pollutants. For the highest congestion scenario, which includes a 200% increase in vehicle volume, total emissions increase by around 460% for PM_2.5 and NO_x, and 540% for CO, SO₂, GHGs, and NMHC over uncongested conditions for a two-hour period. Expedited processing and queue reduction can reduce emissions in this highest congestion scenario by as much as 16% for PM_2.5, 18% for NO_x, 20% for NMHC, 7% for SO₂ and 15% for GHGs and CO. Other potential mitigation strategies examined include fleet upgrades, fuel switching, and fuel upgrades. Adoption of some or all of these changes would not only reduce emissions at the Mariposa POE, but would have air-quality benefits for nearby populations in both the US and Mexico. Fleet-level changes could have far-reaching improvements in air quality on both sides of the border.     

Mitigating air pollution impacts of passenger ferries

Increasing regional mobility demand amid rising roadway congestion has motivated plans for passenger ferry expansion and modernization in many parts of the US. While this trend applies to ferry systems in Alaska, New York, Boston, and Washington state, efforts to expand ferry service in the San Francisco Bay Area are unique in scale and vision. Integrating ferry service into the regional, door-to-door transit system can significantly increase water-crossing capacity for commuters. However, to realize this potential, the ferry industry must meet several challenges associated with growth, including environmental impacts. In particular, concern over air pollution emissions from marine engines is motivating new comparisons between ferries and other transportation modes in terms of both mobility and air pollution. This paper describes the current debate about ferry system operation and expansion, and presents a parametric analysis comparing existing, uncontrolled ferry emissions to automobiles. Under all reasonable assumptions, we show that diesel-powered ferries without emissions controls will produce more NO_x and PM, but less CO per passenger-trip than if those people commuted by car under current conditions. This paper also projects the emissions from the expanded ferry system proposed for the San Francisco Bay Area, showing that a larger ferry fleet equipped with new engines meeting future EPA emissions standards could become one of the major non-road NO_x sources in the region. We conclude by outlining the alternatives and challenges to reduce ferry emissions so that they are more comparable to automobile emissions. Policy implications of these alternatives are also discussed.     

Identifying contributions of on-road motor vehicles to urban air pollution using travel demand model data

Ambient concentrations of pollutants are correlated with emissions, but the contribution to ambient air quality of on-road mobile sources is not necessarily equal to their contribution to regional emissions. This is true for several reasons such as the distribution of other pollution sources and regional topology, as well as meteorology. In this paper, using a dataset from a travel demand model for the Sacramento metropolitan area for 2005, regional vehicle emissions are disaggregated into hourly, gridded emission inventories, and transportation-related concentrations are estimated using an atmospheric dispersion model. Contributions of on-road motor vehicles to urban air pollution are then identified at a regional scale. The contributions to ambient concentrations are slightly higher than emission fractions that transportation accounts for in the region, reflecting that relative to other major pollution sources, mobile sources tend to have a close proximity to air quality monitors in urban areas. The contribution results indicate that the impact of mobile sources on PM₁₀ is not negligible, and mobile sources have a significant influence on both NO_x and VOC pollution that subsequently results in secondary particulate matter and ozone formation.     

The role of light duty vehicles in future air pollution: a case study of Sacramento

Abstract

On-road light-duty vehicles (LDVs) play an important role in contributing to urban air pollution. Although vehicles are getting cleaner, regional growth in vehicle population and vehicle miles traveled would somewhat offset California's efforts in transportation pollution reduction. To better understand the role of LDVs in future air pollution, we conduct a case study for Sacramento, California, and investigate future trends in urban air pollution attributable to the light-duty fleet. Results indicate that ambient concentrations of CO, NO _x , and total organic gases (TOGs) caused by future light-duty fleets would dramatically decrease over coming years. The resulting concentrations in 2030 might be as low as approximately 20% of the 2005 concentrations. These reflect the improvements in vehicle/fuel technologies and standards in California. However, the future particulate matter (PM₁₀) pollution could be slightly worse than that caused by the 2005 fleet. This is a result of the growing fleet-average emission factors of particulates from 2005 to 2030. For purposes of future particulate control, more attention needs to be paid to LDVs, besides heavy-duty vehicles.     

Estimation of nitrogen oxides emissions from petrol and diesel passenger cars by means of on-board monitoring: Effect of vehicle speed,vehicle technology,engine type on emission rates

NO_X emission rates of 13 petrol and 3 diesel passenger cars as a function of average speed from 10 to 120 km/h, emission class (pre-Euro 1 – Euro 5), engine type were investigated by on-board monitoring on roads and highways of St. Petersburg using a portative Testo XXL 300 gas analyzer. The highest level of NO_X emission 0.5–2.5 g/km was inherent to old pre-Euro 1 petrol cars without a catalytic converter. NO_X emissions rates of Euro 1 and Euro 2 petrol cars changed within 0.15–0.9 g/km, Euro 3 – 0.015–0.27 g/km, Euro 4 – 0.013–0.1 g/km, Euro 5 – 0.002–0.043 g/km. Euro 3 – Euro 4 petrol cars generally satisfied corresponding NO_X Emission Standards (ES), except cold-start period, Euro 5 petrol cars did not exceed ES. Warmed, stabilized engines of Euro 3 – Euro 5 petrol cars showed 5–10 times lower NO_X emission rates than corresponding ES in the range of speed from 20 to 90 km/h. NO_X emission rates of diesel Euro 3 and Euro 4 cars varied from 0.45 to 1.1 g/km and from 0.31 to 1.1 g/km, respectively. Two examined diesel Euro 3 and one Euro 4 passenger vehicles did not satisfy NO_X ES at real use. Euro 3 diesel cars showed 28.9 times higher NO_X emissions than Euro 3 petrol cars and Euro 4 diesel car demonstrated 17.6 times higher NO_X emissions than Euro 4 petrol cars at warmed and stabilized engine at a cruise speed ranging from 30 to 60 km/h.     

PM2.5 and NOx from traffic: Human health impacts,external costs and policy implications from the Belgian perspective

This article employs an optimized impact pathway approach to marginal external health costs that relies on high-resolution dispersion models calibrated for Belgium and the surrounding areas. Per tonne, the MEHC_PM2.5 is found to be many times larger than MEHC_NOx, which is currently negative. Further, the impact of Belgian PM_2.5 emissions in the immediate area of generation is significantly larger than the impact on more distant areas; the opposite is true for NO_x. The MEHCs of both pollutants are predicted to increase in the coming years. Further analysis of the impacts of PM_2.5 and NO_x reveals that, on average, modern gasoline vehicles outperform their diesel counterparts as far as future emissions are concerned. This contrasts with findings for 2007, which suggested that Euro 5 diesels had fewer associated health costs because of the potential for ozone reduction offered by their NO_x emissions.     

Individual exposure to traffic related air pollution across land-use clusters

In this study, we estimated the transportation-related emissions of nitrogen oxides (NO_x) at an individual level for a sample of the Montreal population. Using linear regression, we quantified the associations between NO_x emissions and selected individual attributes. We then investigated the relationship between individual emissions of NO_x and exposure to nitrogen dioxide (NO₂) concentrations derived from a land-use regression model. Factor analysis and clustering of land-uses were used to test the relationships between emissions and exposures in different Montreal areas. We observed that the emissions generated per individual are positively associated with vehicle ownership, gender, and employment status. We also noted that individuals who live in the suburbs or in peripheral areas generate higher emissions of NO_x but are exposed to lower NO₂ concentrations at home and throughout their daily activities. Finally, we observed that for most individuals, NO₂ exposures based on daily activity locations were often slightly more elevated than NO₂ concentrations at the home location. We estimated that between 20% and 45% of individuals experience a daily exposure that is largely different from the concentration at their home location. Our findings are relevant to the evaluation of equity in the generation of transport emissions and exposure to traffic-related air pollution. We also shed light on the effect of accounting for daily activities when estimating air pollution exposure.     

Real-world gaseous and particle emissions of a Bi-fuel gasoline/CNG Euro 6 passenger car

The objective of the present study is the assessment of the environmental impact of a bivalent (bi-fuel) vehicle, running either on gasoline or compressed natural gas (CNG). To that aim, a Euro 6 passenger car was tested under various real-world driving conditions. In order to cover the full range of conventional powertrains currently in the market, the tests were also repeated on a Euro 6 diesel passenger car. Both cars were driven in two routes, the first complying with the regulation limits and the second going beyond them. Carbon monoxide (CO), nitrogen oxides (NO_x) and particle number (PN) emissions were recorded using a Portable Emissions Measurement System (PEMS). Apart from the aggregated emission levels, in g/km, the exact emission location along the route was also assessed. Natural gas proved beneficial for CO and PN emissions, the level of which always remained below the respective legislation limits. On the other hand, under the dynamic driving conditions with gasoline, the relevant limits were exceeded. Cold start, occurring at the beginning of the urban part, and motorway driving were identified as major contributors to total emissions, especially in gasoline mode. However, the application of natural gas was associated with a penalty in NO_x emissions, which were significantly increased as compared to gasoline. Local peaks within the urban part were identified in CNG mode. In any case, the diesel vehicle was by far the highest NO_x emitter.     

Simulating the air quality impacts of traffic calming schemes in a dense urban neighborhood

In this study, the effects of isolated traffic calming measures and area-wide calming schemes on air quality in a dense neighborhood were estimated using a combination of microscopic traffic simulation, emission, and dispersion modeling. Results indicated that traffic calming measures did not have as large an effect on nitrogen dioxide (NO₂) concentrations as the effect observed on nitrogen oxide (NO_x) emissions. Changes in emissions resulted in highly disproportional changes in pollutant levels due to daily meteorological conditions, road geometry and orientation with respect to the wind. Average NO₂ levels increased between 0.1% and 10% with respect to the base-case while changes in NO_x emissions varied between 5% and 160%. Moreover, higher wind speeds decreased NO₂ concentrations on both sides of the roadway. Among the traffic calming measures, speed bumps produced the highest increases in NO₂ levels.     

The costs and benefits of reducing SO2 emissions from ships in the US West Coastal waters

Potential costs and benefits of policy options for reducing offshore ship pollution are examined using a meta-analysis of studies synthesized regionally for the US West Coast. Net benefits of reducing SO₂ emissions from cargo ships in the US West Coast waters are found to range between $98 million and $284 million, annually; the benefit–cost ratio varies between 1.8 and 3.36, depending on the size of the control area and the sulfur content limit. The results show that about 21,000 tons of on-land equivalent SO₂ emissions or about 33% of SO₂ emissions from all mobile sources in California in 2005 can be reduced annually if the US West Coast exclusive economic zone is designated as an International Maritime Organization-compliant SO_x emission control area (SECA) with fuel-sulfur content not exceeding 1.5%. The analysis demonstrates that designating this area reduces more emissions than establishing a smaller zone at a lower but favorable benefit-cost ratio. Control measures that require 0.5% low-sulfur fuels reduce more SO₂ emissions, and also may have higher net benefits. Technological alternatives may achieve benefits of emissions reductions on the US West Coast across higher ranges of potential fuel prices. Combinations of fuel switching and control technology strategies provide the most cost-effective benefits from SECAs on the US West Coast and other world regions.     

An assessment of pollutant emissions due to air traffic at Nikola Tesla International Airport,Belgrade, and the link between local air quality and weather types

The assessment of local air pollution due to air traffic is an important issue from the standpoint of human health. An advanced approach using a landing and take-off cycle method is employed to assess emissions of nitrogen oxides (NO_x), carbon monoxide (CO), hydrocarbon (HC), and sulphur oxides (SO_x). Emissions of both volatile and non-volatile particulate matter are estimated using the new First-Order Approximation methodology. As synoptic situations (weather) determine the transport of pollutants in the air as well as their scavenging, the weather type for each day is classified for the study period (2008–2015).Due to a significant increase in air traffic at Nikola Tesla International Airport, Belgrade, in the last eight years, emissions of all considered pollutants have also increased. Emissions of NO_x and CO were the highest (totals for eight years were 2976.03 and 2875.66 tons, respectively). An analysis of weather types showed that the most frequent were warm, dry, anticyclones (AWD) and cyclones (low-pressure systems) including the passage of a cold front (CCF). The frequency of occurrence of AWDs and CCFs was 28.3% and 21.6%, respectively. An AWD is very unfavourable from the viewpoint of local air pollution, especially during the cold part of year, due to a shallow temperature inversion and fog formation in the morning confining the pollutants to the emission location for a longer time span. CCFs are also adverse due to the prevailing westerly and north-westerly winds that transport pollutants toward the city.     

High-speed rail's potential for the reduction of carbon dioxide emissions from short haul aviation: a longitudinal study of modal substitution from an energy generation and renewable energy perspective

Abstract

This paper quantifies and evaluates, utilising a ‘bottom-up’ approach, the effect on CO₂ emissions of a modal shift from short-haul air travel to high-speed rail (HSR), based on projected passenger movements, between Sydney and Melbourne, Australia during the period 2010–2030. To date, peer-reviewed studies assessing the CO₂ emissions from these competing modes of high-speed transportation have been restricted principally to a cross-sectional assessment, with a Eurocentric bias. This present comparative study seeks to address a gap in the literature by assessing, longitudinally, the CO₂ emissions associated with the proposed operation of HSR against the ‘business-as-usual’ air scenario between Sydney and Melbourne. Under the assumed 50/50 modal shift, and the Australian government's current renewable electricity target, an annual reduction in CO₂ emissions of approximately 14% could be achieved when compared with a ‘business-as-usual’ air scenario. This percentage reduction represents a 62 kt reduction in base year, 2010, and a 114 kt reduction in the final year, 2030. In total, the overall reduction achieved by such a modal shift, under the assumed conditions, during the period 2010–2030, equates to approximately 1.87 Mt of CO₂. Importantly, if the electrical energy supply for HSR operations was further ‘decarbonised’, then it follows that a greater emission reduction would be achieved.     

Light duty gasoline vehicle emission factors at high transient and constant speeds for short road segments

Vehicle emissions estimates are needed at high spatial and temporal resolution to estimate near-roadway air quality and human exposures. The MOBILE6 emission factor model is based on transient test cycles of less than 65 mph. Correction factors for high speed and constant speed are developed based on vehicle-specific power-based modal models for light duty gasoline vehicles, using data from portable emission measurement systems. At 80 mph versus 65 mph, the estimated average emission rates are greater by 30%, 20%, 80%, and 10% for NO_x, HC, CO, and CO₂. The ratio of constant to average of transient speed emission rates range from 0.49 to 0.94 for NO_x at speeds of 20 mph and 80 mph. The high speed and constant speed correction factors are applied to estimate vehicle emissions for a freeway segment that includes vehicle cruising speeds between 65 and 80 mph. The potential error for not accounting for constant speed operation on a short segment of highway could be 49% at moderate speed and 24% at high speed.     

Energy use and emissions of two stroke-powered tricycles in Metro Manila

CO, CO₂, NO_x and HC emissions of two stroke-powered tricycles in Metro Manila are examined using an instantaneous emissions model. Results show that fuel consumption and HC emissions in middle class residential areas and main roads are similar but lower than levels in low income residential areas. On the average, tricycles in Metro Manila consume 24.41 km/l of fuel and produces 9.5, 9.7, 40.5 and 0.07 g/km of HC, CO, CO₂ and NO_x, respectively. They fail to satisfy HC, CO and NO_x emission limits set by reference standards in the Philippines and other Asian countries. They produce greater HC and CO emissions than gasoline fueled private cars and diesel powered public jeepneys, taxis and buses on a per passenger-km basis but significantly lower NO_x emissions. Tricycles account for 15.4% of the total HC emissions from mobile sources in the metropolis while their contributions to CO, CO₂ and NO_x are minimal.     

Policy innovations of the US intermodal surface transportation efficiency act and clean air act amendments

In combination, the Intermodal Surface Transportation Efficiency Act of 1991 (ISTEA) and the Clean Air Act Amendments of 1990 (CAAA) are innovative and aggressive efforts to move US cities toward integrated transportation and air quality planning. Under these complementary laws, air quality has become a major national transportation goal. In areas with serious air pollution, air quality will be a major consideration in determining the future shape of urban transportation.This paper considers how the CAAA and ISTEA combine to provide an innovative national policy approach of interest to countries seeking to encourage sustainable development in urban centers. The CAAA mandates measurable and enforceable air quality targets. Nation-wide standards are set for acceptable levels of carbon monoxide, ground level ozone, and small particulates. ISTEA includes directions for transportation planners and decision-makers to follow to reach air quality and other goals — transportation planning must emphasize system efficiency, and for cities with severe air pollution, transportation projects are expected to contribute to cleaner air. Each urban area has flexibility in how it applies this framework to reflect its priorities and solve its problems. Strict federal sanctions provide incentives for compliance with both laws.Enactment of these laws has produced a period of transition and uncertainty as well as of challenge and opportunity for planners and elected officials. The next several years, the US will provide one national laboratory and over 100 different urban laboratories for innovative approaches to integrate transportation and environmental policies to resolve major urban problems.Abbreviations CAAA Clean Air Act Amendments of 1990 - CO Carbon monoxide - ECO Employee Commute Option - EPA US Environmental Protection Agency - HC Transportation hydrocarbons - I/M Inspections and maintenance program - ISTEA Intermodal Surface Transportation Efficiency Act of 1991 - MPO Metropolitan planning organizations - NO_x Nitrogen oxides - PPM Parts per million - PM₁₀ Small particulate matter - SIP State Implementation Plan - TIP Transportation Improvement Program - TCM Transportation control measures - VMT Vehicle miles traveled     

Comparing air pollution from ferry and landside commuting

Recent and anticipated growth in passenger ferry service has been complicated by concerns about air pollution from marine engines that are only starting to be regulated. While marine engines are known to be a significant and growing source category in some locations, sparse data and analytical difficulties have prevented rigorous comparisons of marine and on-land passenger travel. Using data gathered in the San Francisco Bay Area, we model emissions from three passenger ferries and the matching on-land travel that would be used by commuters if ferry service were not available. The results are analyzed parametrically for levels of ridership and induced travel demand, and for new technologies, including selective catalytic reduction and natural gas fuel. Results indicate that under some conditions, passenger ferries reduce some emissions (including particulate matter emissions) relative to the matching on-land service but increase others. Emissions of NO_X are particularly problematic––all the technologies examined lead to increased NO_X emissions due to ferry commuting. Some of the emissions comparisons are sensitive to mode split, ridership, or induced travel demand. However, NO_X emissions are not––ferry commuting always raises NO_X emissions, even with the most advanced technologies. Implications for local air quality regulators and for technology development are discussed.     

Development of an emissions inventory model for mobile sources

Traffic represents one of the largest sources of primary air pollutants in urban areas. As a consequence, numerous abatement strategies are being pursued to decrease the ambient concentrations of a wide range of pollutants. A mutual characteristic of most of these strategies is a requirement for accurate data on both the quantity and spatial distribution of emissions to air in the form of an atmospheric emissions inventory database. In the case of traffic pollution, such an inventory must be compiled using activity statistics and emission factors for a wide range of vehicle types. The majority of inventories are compiled using ‘passive’ data from either surveys or transportation models and by their very nature tend to be out-of-date by the time they are compiled. Current trends are towards integrating urban traffic control systems and assessments of the environmental effects of motor vehicles. In this paper, a methodology for estimating emissions from mobile sources using real-time data is described. This methodology is used to calculate emissions of sulphur dioxide (SO₂), oxides of nitrogen (NO_x), carbon monoxide (CO), volatile organic compounds (VOC), particulate matter less than 10 μm aerodynamic diameter (PM₁₀), 1,3-butadiene (C₄H₆) and benzene (C₆H₆) at a test junction in Dublin. Traffic data, which are required on a street-by-street basis, is obtained from induction loops and closed circuit televisions (CCTV) as well as statistical data. The observed traffic data are compared to simulated data from a travel demand model. As a test case, an emissions inventory is compiled for a heavily trafficked signalized junction in an urban environment using the measured data. In order that the model may be validated, the predicted emissions are employed in a dispersion model along with local meteorological conditions and site geometry. The resultant pollutant concentrations are compared to average ambient kerbside conditions measured simultaneously with on-line air quality monitoring equipment.     

Estimating mortality impacts from vehicle emission reduction efforts: The Tune In and Tune Up program in the San Joaquin Valley

As a response to profoundly poor air quality and associated environmental justice concerns in the San Joaquin Valley region in California, the Tune In & Tune Up (TI&TU) program provides residents with free vehicle emissions testing and vouchers for smog repair. We used data on approximately 19,000 repaired TI&TU vehicles from 2012 to 2018, and several estimation techniques, to quantify a range of nitrogen oxides (NO_X) emissions prevented as a result of the program. We then calculated resulting mortality impacts from reduced exposure to fine particulate matter (PM_2.5) in the form of secondary nitrates. After applying a novel smog repair emissions abatement depreciation function, we find that six years of operation of the TI&TU program has reduced NO_X emissions by approximately 53–302 tons by the end of 2018. Using a concentration response function for ambient PM_2.5, we found that between 0.055 and 0.31 premature deaths have also been avoided. We present multiple methods for assessing public health impacts, which can be used as guidance for evaluating similar transportation-based emission reduction programs.