基于Boost的柴油机微粒捕集器(DPF)性能分析

柴油机微粒排放控制技术已成为柴油机技术发展中的核心之一。文中探讨了微粒捕集器的捕集机理、过滤体材料特性以及再生技术。并利用AVL Boost软件建立模型,仿真分析了发动机的排气温度和柴油机微粒捕集器(Diesel Particulate Filter,DPF)的过滤孔密度对DPF的最高温度、排气背压和排气碳烟量的影响,提出了柴油机微粒捕集器设计优化的方法。     

柴油机微粒捕集器再生技术研究

柴油机排气微粒捕集器技术是实现柴油机微粒排放控制最有效的技术。而柴油机微粒捕集器的关键技术是过滤材料和再生方法的研究,本文在介绍其过滤材料和再生方法的基础上,对比分析和研究了其特点和主要问题。对系统中各类再生系统的结构和性能进行了分析比较,阐明了其优缺点和技术可行性。     

基于添加剂和电加热的柴油机DPF再生技术研究

提出了基于添加剂和电加热的柴油机微粒捕集器再生技术,以柴油添加剂与电加热相结合的方式,利用柴油添加剂降低微粒起燃温度,再生时补充少许空气,只需少量的电能就可以点燃微粒,通过其自身火焰的蔓延来完成整个捕集器的再生。以SOFIM8140.27柴油机为对象,对微粒捕集及再生方案进行了大量试验研究,证实了该设计方案具有捕集效率高、再生可靠和车载实用等优点,能够适应我国的燃油品质。     

柴油机微粒捕集器燃油添加剂催化再生的试验研究

通过在康明斯6BT5.9发动机柴油中加入某型燃油添加剂的试验表明,添加剂能使沉积在捕集器内的微粒在300～400℃时起燃而使捕集器再生.同时分析了不同工况下,微粒累积与再生平衡温度点的变化及再生效果的优劣.对柴油机微粒捕集器再生技术的研究具有一定指导意义.     

柴油机大客车排放的机外净化技术

柴油机大客车的机外净化技术的装置主要是为了减少微粒、HC、CO和NOx等有害气体,可以采用的如下具体结构来完成：微粒捕集器和再生微粒捕集器、氧化催化转化器、NOx还原催化转化器。     

柴油机排气微粒捕集器燃气再生可行性研究

提出了一种新的柴油机排气微粒捕集器的再生技术 ,即利用燃气与排气中的O2 燃烧清除微粒捕集器中沉积的微粒 (PM)。根据燃气的物化特性和排气中的含O2 量 ,对这种方法的可行性进行了理论分析和试验验证 ,为解决柴油机PM排放控制提供了一条新的技术途径     

An Experimental Study on the Technology of Diesel Particulate Filter Regeneration

微粒捕集器结合氧化催化器是被广泛采用的柴油机后处理技术路线.本文中设计了一套燃油雾化喷射系统,可更好地协助氧化催化器工作,将发动机的排气温度提升到微粒的起燃温度,台架验证试验结果表明,该系统能很好地实现微粒捕集器的再生.     

柴油机微粒捕集器瞬态再生特性仿真

建立了基于柴油机微粒捕集器主动再生的GT-Power仿真模型,针对2 200 r/min、100%和1 400 r/min、50%两种典型工况,对捕集器瞬态再生特性进行了研究。计算结果表明：柴油机由高转速、大负荷变为低转速、小负荷的瞬态工况下,微粒捕集器再生时,载体各端温度曲线呈双峰状,载体壁面峰值温度与稳态相比大大升高;且工况变化时间越短,这种现象越明显。     

柴油机排气颗粒物捕集器的发展

柴油机在轻型车辆上使用的日趋普遍,使得柴油机排放气体中的颗粒物后处理成为研究热点。颗粒物捕集器是解决柴油机排气颗粒污染最有效的后处理技术。针对目前国内颗粒物捕集器的使用情况,论述了柴油机排气颗粒物捕集器过滤材料和过滤体再生技术近年来的研究现状,介绍了近年来过滤材料和过滤体再生技术结合良好的几种颗粒物捕集器,提出了颗粒物捕集器今后的研究方向。     

柴油机微粒捕集器定工况主动再生条件的试验研究

柴油机尾气后处理系统采用仅安装氧化催化转化器方案,通过试验确定了柴油机微粒捕集器定工况主动再生时所需的入口条件,通过对发动机不同工况排气温度的测量确定了微粒捕集器定工况主动再生的发动机工况点,得出了主动再生时排气管中所需喷入液化石油气的喷射脉宽.试验中氧化催化转化器对HC的转化效率达到了90%以上,满足了再生期间对催化...     

柴油机颗粒物后处理技术综述

通过调研国内外文献,介绍了柴油机颗粒物污染现状、颗粒物后处理技术、壁流式颗粒捕集器(DPF)的工作原理、材料和结构类型、捕集器再生技术和控制策略等。堇青石陶瓷壁流式DPF具有成本和性能方面的优势,占据主要市场份额,再生技术是DPF应用的关键。与主动再生技术相比,被动再生具有结构简单、节约油耗等优势,可通过涂敷催化剂、前置DOC和辅助主动再生等方法确保再生效果。     

柴油机微粒捕集器催化再生技术

柴油机微粒捕集器（DPF）能降低柴油机的微粒（PM）排放量,文章提出了DPF催化再生技术方案,将氧化催化器（DOC）与DPF相结合,通过DOC催化氧化未燃HC等来提高排气温度达到微粒着火温度500～600℃,点燃微粒从而完成再生过程。以YN4100QB–1A柴油机为研究对象,对不同喷油量下的DPF升温特性进行了试验研究,试验结果表明：当喷油量大于60mL/min时,再生系统能迅速将排气温度提高到500℃以上。可变喷油量的喷油控制方案可使DPF升温平缓,降低再生造成的二次污染。     

Computational study on the effects of volume ratio of DOC/DPF and catalyst loading on the PM and NOx emission control for heavy-duty diesel engines

The use of a diesel particulate filter (DPF) in a diesel aftertreatment system has proven to be an effective and efficient method for removing particulate matter (PM) in order to meet more stringent emission regulations without hurting engine performance. One of the favorable PM regeneration technologies is the NO₂-assisted regeneration method due to the capability of continuous regeneration of PM under a much lower temperature than that of thermal regeneration. In the present study, the thermal behavior of the monolith during regeneration and the conversion efficiency of NO₂ from NO with an integrated exhaust system of a diesel oxidation catalyst (DOC) and DPF have been predicted by one-channel numerical simulation. The simulation results of the DOC, DPF, and integrated DOC-DPF models are compared with experimental data to verify the accuracy of the present model for the integrated DOC and DPF modeling. The effects of catalyst loading inside the DOC and the volume ratio between the DOC and DPF on the pressure drop, the conversion efficiency, and the oxidation rate of PM, have been numerically investigated. The results indicate that the case of the volume ratio of ‘DOC/DPF=1.5’ within the same diameter of both monoliths produced close to the maximum conversion efficiency and oxidation rate of PM. Under the engine operating condition of 175 kW at 2200 rpm, 100% load with a displacement of 8.1, approximately 55 g/ft³ of catalyst (Pt) loading inside the DOC with the active Pt surface of 5.3 m²/g_pt was enough to maximize the conversion efficiency and oxidation rate of PM.     

共轨柴油机排气后处理系统实时仿真模型

柴油机从欧Ⅲ排放标准发展到欧Ⅳ排放标准需要增加排气后处理系统,对排气后处理系统的建模和仿真将是欧Ⅳ柴油机控制系统开发流程中的重要环节。介绍了排气后处理系统的发展状况,针对柴油机控制系统开发建立了排气后处理系统模型,包括氧化催化器和微粒过滤器两个模块,模型根据能量守恒和化学动力学原理建立。对后处理模型进行了硬件在环仿真,对微粒过滤器的再生策略进行了分析。     

国六柴油机颗粒物捕集器在工程应用中的关键问题分析

通过分析国六排放法规,并结合对OEM(Original Equipment Manufacturer)市场国六后处理技术的开发以及我国的特殊地理环境,总结了国六柴油机颗粒物捕集器(Diesel Particulate Filter,DPF)开发的重点、难点问题。综合来看,开发高目数、薄壁、非对称孔道结构及高强度的DPF载体是国六柴油机面临的关键问题。同时,DPF的高原捕集再生特性也是值得深入研究的核心问题。新一代国六DPF主要面临以下技术难题:(1)DPF压降与捕集效率的折衷关系,尤其是对颗粒物数量(Particle Numbers,PN)的捕集效率需要在99%以上。(2)DPF的捕集再生特性决定了其作为流-固-热多场耦合装置需要与控制策略协同优化,才能避免DPF爆燃现象的发生,提高载体可靠性和耐久性。(3)高原地区低压、低氧的特殊环境导致发动机原排PM/PN较高,同时颗粒物理化特性变化较大,且山路驾驶工况复杂多变,对DPF的高效捕集再生及可靠性要求提出了更大挑战。     

DOC辅助DPF再生的二次污染研究

在氧化型催化转换器(DOC)前端的排气管中喷入柴油,通过提高柴油机尾气温度、燃烧并去除柴油机微粒捕集器(DPF)中的PM,实现了DPF再生。对整个再生过程中尾气成分进行分析和计算,发现碳氢化合物(HC)为主要二次污染物,且排放相对较大。通过试验方法,分别研究喷油流量和喷油时DOC前端排气温度对再生过程中HC排放的影响,并依此提出保温处理、分阶段喷油和低速再生等三项优化措施。优化后再生过程中HC排放降低了68%,且燃油经济性提高了21%。     

Carbon Deposit Incineration During Engine Flameout Using Non-Thermal Plasma Injection

In order to investigate the influence of initial regeneration temperatures on diesel particulate filter (DPF) regeneration, an experimental study of DPF regeneration was implemented using a dielectric barrier discharge (DBD) reactor, aided by exhaust waste heat after engine flameout. DPF trapping characteristics and carbon deposit mass were discussed to facilitate further data analysis and calculation. DPF regeneration was then investigated by comparison analysis of deposit removal mass, backpressure drop, and internal temperature change. The results revealed that a large amount of particulate matter (PM) was deposited in DPF with a high filtration efficiency of about 90 %. The deposit removal rate and percentage drop of the backpressure both maximized at the initial temperature of 100 °C. During DPF regeneration, the sharp rise of internal temperature indicated vigorous PM incineration and high CO₂ emission. The results successfully demonstrated DPF regeneration using non-thermal plasma injection during engine flameout, and prominent heat durability was achieved in this method.     

Effects of Residual Ash on Dpf Capture and Regeneration

To study the effects of residual ash on the capture and regeneration of a diesel particulate filter (DPF), repeated capture and complete regeneration experiments were conducted. An engine exhaust particulate sizer was used to measure the particle size distribution of diesel in the front and back of DPF. Discrepancies in the size distribution of the particulate matter in repeated trapping tests were analyzed. To achieve complete DPF regeneration, a DPF regeneration system using nonthermal plasma technology was established. The regeneration carbon removal mass and peak temperatures of DPF internal measuring points were monitored to evaluate the effect of regeneration. The mechanism explaining the influence of residual ash on DPF capture and regeneration was thoroughly investigated. Results indicate that the DPF trapping efficiencies of the nuclear-mode particles and ultrafine particles have significant improvements with the increase quantity of residual ash, from 90 % and 96.01 % to 94.17 % and 97.27 %, respectively. The exhaust backpressure of the DPF rises from 9.41 kPa to 11.24 kPa. Heat transfer in the DPF is improved with ash, and the peak temperatures of the measuring points accordingly increase. By comparing the regeneration trials, the elapsed time for complete regeneration and time difference for reaching the peak temperature between adjacent reaction interfaces are extended with increased quantity of ash. The carbon removal mass rises by 34.00 %.     

采用燃烧器+氧化催化器的柴油机微粒捕集器复合再生控制策略的研究

设计了一种车载全流式燃烧器,从增压柴油机的涡轮增压器取出新鲜空气,从回油管路取油供给燃烧;将该装置安装在排气管尾端使捕集器进行再生.在燃烧器和捕集器之间增加氧化催化器,实现了在发动机所有稳态工况下捕集器的复合再生.在排气背压的再生控制策略基础上,根据经验公式对背压值进行温度修正,将三维背压MAP简化为二维,提出"恒温定时"的复合再生控制策略,分析了控制策略在不同工况区域的运用,给出了再生过程分析实例.对既定的控制策略进行了实车试验,结果表明微粒排放达到了国Ⅳ标准.