A model of driver steering control incorporating the driver's sensing of steering torque

Steering feel, or steering torque feedback, is widely regarded as an important aspect of the handling quality of a vehicle. Despite this, there is little theoretical understanding of its role. This paper describes an initial attempt to model the role of steering torque feedback arising from lateral tyre forces. The path-following control of a nonlinear vehicle model is implemented using a time-varying model predictive controller. A series of Kalman filters are used to represent the driver's ability to generate estimates of the system states from noisy sensory measurements, including the steering torque. It is found that under constant road friction conditions, the steering torque feedback reduces path-following errors provided the friction is sufficiently high to prevent frequent saturation of the tyres. When the driver model is extended to allow identification of, and adaptation to, a varying friction condition, it is found that the steering torque assists in the accurate identification of the friction condition. The simulation results give insight into the role of steering torque feedback arising from lateral tyre forces. The paper concludes with recommendations for further work.     

The Influence of Structural Flexibilities on the Straight-running Stability of Motorcycles

SUMMARY

A new tyre model for studies of motorcycle lateral dynamics, and three new motorcycle models, each incorporating a different form of structural compliance, are developed. The tyre model is based on “taut string” ideas, and includes consideration of tread width and longitudinal tread rubber distortion and tread mass effects, and normal load variation. Parameter values appropriate to a typical motorcycle tyre are employed. The motorcycle models are for small lateral perturbations from straight running at constant speed, and include (a) lateral compliance of the front wheel in the front forks, (b) torsional compliance of the front forks, and (c) torsional compliance in the rear frame at the steering head about an axis perpendicular to the steering axis.

Results in the form of eigenvalues, indicating modal damping properties and natural frequencies are presented for each model. The properties of four large production machines for a range of forward speeds, and the practicable range of stiffnesses are calculated, and the implications are discussed.

It is concluded that typical levels of structural compliance in models (a) and (c) contribute significantly to the steering behaviour properties of large motorcycles, and their observed behaviour can be understood better in terms of the new results than of those existing previously. Some conclusions relating to optimal structural stiffness properties are also drawn.     

Investigation of Features of Tyre Rolling at Non-Small Velocities on the Basis of a Simple Tyre Model with Distributed Mass Periphery

SUMMARY

On the basis of the brush-type tyre model the paper considers the interaction between steady-state rolling deformable wheel and flat road surface as well as corresponding force and moment characteristics of the wheel.

At least two zones of sliding, anisotropic dry friction, sliding friction coefficient speed-dependent and instantaneous leap of the friction coefficient when transition from sliding to adhesion zone occurs, have been taken into account, as well as distributed peripheral mass of tyre, elasticity, pseudo-dry friction and damping properties in radial, tangential and lateral directions of the elements at the wheel periphery, including a visco-elastic belt. Vertical force distribution in the contact area is not supposed to be known in advance and follows from the calculation. As a result, sliding zone lengths, distributed forces in contact area, six components of generalized road reaction reduced to the wheel center, and rolling resistance moment are found as functions of vertical load, movement velocity, longitudinal and side slip, friction in contact area with road, stiffnesses, dry friction and damping in the tyre model elements and of distributed peripheral mass.

A computer program developed in Fortran and results of calculations are of particular interest for qualitative analysis including steady rolling of studded tyre and also racing car and aircraft tyres which peripheral mass shows itself in a special way because of great movement velocities.     

Steady Turning of Two-Wheeled Vehicles

When driving along a circular path, the driver of a motorcycle controls the vehicle mainly by means of steering torque. If low steering torque is necessary, the driver feels that the vehicle is manoeuvrable. In this paper, a mathematical model concerning steering torque is developed; it takes into account the actual kinematic behaviour of the vehicle and the properties of motorcycle tyres. Tyre forces act at the contact points of toroidal tyres, which are calculated according to kinematic analysis. Non-linear equations are solved using an iterative approach. Several numerical results are presented, and the influence of tyre properties and some geometrical and inertial properties of the vehicle on steering torque are discussed.     

Tyre–road grip coefficient assessment – Part II: online estimation using instrumented vehicle,extended Kalman filter,and neural network

The main objective of this work is to determine the limit of safe driving conditions by identifying the maximal friction coefficient in a real vehicle. The study will focus on finding a method to determine this limit before reaching the skid, which is valuable information in the context of traffic safety. Since it is not possible to measure the friction coefficient directly, it will be estimated using the appropriate tools in order to get the most accurate information. A real vehicle is instrumented to collect information of general kinematics and steering tie-rod forces. A real-time algorithm is developed to estimate forces and aligning torque in the tyres using an extended Kalman filter and neural networks techniques. The methodology is based on determining the aligning torque; this variable allows evaluation of the behaviour of the tyre. It transmits interesting information from the tyre–road contact and can be used to predict the maximal tyre grip and safety margin. The maximal grip coefficient is estimated according to a knowledge base, extracted from computer simulation of a high detailed three-dimensional model, using Adams^® software. The proposed methodology is validated and applied to real driving conditions, in which maximal grip and safety margin are properly estimated.     

Steady Turning of Two-Wheeled Vehicles

When driving along a circular path, the driver of a motorcycle controls the vehicle mainly by means of steering torque. If low steering torque is necessary, the driver feels that the vehicle is manoeuvrable. In this paper, a mathematical model concerning steering torque is developed; it takes into account the actual kinematic behaviour of the vehicle and the properties of motorcycle tyres. Tyre forces act at the contact points of toroidal tyres, which are calculated according to kinematic analysis. Non-linear equations are solved using an iterative approach. Several numerical results are presented, and the influence of tyre properties and some geometrical and inertial properties of the vehicle on steering torque are discussed.     

Common underlying steering curves for motorcycles in steady turns

We study the steady turn behaviours of some light motorcycle models on circular paths, using the commercial software package ADAMS-Motorcycle. Steering torque and steering angle are obtained for several path radii and a range of steady forward speeds. For path radii much greater than motorcycle wheelbase, and for all motorcycle parameters including tyre parameters held fixed, dimensional analysis can predict the asymptotic behaviour of steering torque and angle. In particular, steering torque is a function purely of lateral acceleration plus another such function divided by path radius. Of these, the first function is numerically determined, while the second is approximated by an analytically determined constant. Similarly, the steering angle is a function purely of lateral acceleration, plus another such function divided by path radius. Of these, the first is determined numerically while the second is determined analytically. Both predictions are verified through ADAMS simulations for various tyre and geometric parameters. In summary, steady circular motions of a given motorcycle with given tyre parameters can be approximately characterised by just one curve for steering torque and one for steering angle.     

Tyre friction behaviour under abrupt wheel torque transients on slippery road surfaces: experimental analysis and modelling

The paper shows that, during abrupt wheel torque transients for ice surface and low vehicle speeds, the tyre can develop significantly larger longitudinal force than the peak value of the tyre static curve. This so-called dynamic tyre friction potential (DTFP) effect has many influencing factors such as the rate of change of the wheel torque, the vehicle speed, and the tyre dwell time. The paper presents a detailed analysis of the DTFP behaviour based on the experimental data collected by using an in-wheel motor-based tyre test vehicle. The analysis results and an insight into the brush structure of a tyre model lead to the hypothesis that the different influencing factors may be predominantly explained by the bristle dwell time (BDT) effect. Following this hypothesis, the LuGre model of the tyre friction dynamics is extended with a physical BDT sub-model. The experimental validation results show that the proposed model can accurately capture the low-speed tyre–ice friction behaviour during abrupt wheel torque transients.     

汽车电动助力转向控制系统的初步研究

自行设计的电动助力转向系统(EPS)由控制器、转向盘转矩传感器、车速传感器、电流传感器(在控制器内)、助力电机及减速机构、机械式转向器、蓄电池等组成。EPS的控制系统主要由控制器、传感器及信号处理电路、助力电机及驱动电路等组成。控制算法由电机助力控制算法和电机转矩控制算法两部分构成。该方案易于实现，同时又能保证转向控制系统较高的控制精度。     

The Influence of Structural Flexibilities on the Straight-running Stability of Motorcycles

A new tyre model for studies of motorcycle lateral dynamics, and three new motorcycle models, each incorporating a different form of structural compliance, are developed. The tyre model is based on “taut string” ideas, and includes consideration of tread width and longitudinal tread rubber distortion and tread mass effects, and normal load variation. Parameter values appropriate to a typical motorcycle tyre are employed. The motorcycle models are for small lateral perturbations from straight running at constant speed, and include (a) lateral compliance of the front wheel in the front forks, (b) torsional compliance of the front forks, and (c) torsional compliance in the rear frame at the steering head about an axis perpendicular to the steering axis.

Results in the form of eigenvalues, indicating modal damping properties and natural frequencies are presented for each model. The properties of four large production machines for a range of forward speeds, and the practicable range of stiffnesses are calculated, and the implications are discussed.

It is concluded that typical levels of structural compliance in models (a) and (c) contribute significantly to the steering behaviour properties of large motorcycles, and their observed behaviour can be understood better in terms of the new results than of those existing previously. Some conclusions relating to optimal structural stiffness properties are also drawn.     

Study of the Pneumatic Tyre Behaviour on Dry and Rigid Road by Finite Element Method

SUMMARY

The paper presents a physical tyre model capable of describing the complete pneumatic tyre behaviour during steady and transient states. Given the radial deflection, the longitudinal and lateral slip, the camber angle, the inner pressure and the mechanical parameters describing the tyre structure, the model returns the vertical load, the longitudinal and lateral forces, the self aligning torque. Particular attention has been devoted to the computation (by f.e.m.) of tyre carcass and tread deformations; it is explained how side force increases by moderate braking at constant slip angle. An experimental verification validates the model, although more studies could be needed to improve model effectiveness.     

Noise,vibration, harshness model of a rotating tyre

ABSTRACT

The tyre plays a fundamental role in the generation of acoustically perceptible driving noise and vibrations inside the vehicle. An essential part of these vibrations is induced by the road excitation and transferred via the tyre into the vehicle. There are two basic ways to study noise, vibration, harshness (NVH) behaviour: Simulations in time and frequency domains. Modelling the tyre transfer behaviour in frequency domain requires special attention to the rotation of the tyre. This paper shows the approach taken by the authors to include the transfer behaviour in the frequency range up to 250?Hz from geometric road excitations to resulting spindle forces in frequency domain. This paper validates the derived NVH tyre model by comparison with appropriate transient simulations of the base transient model.     

电动助力转向系统H∞鲁棒控制研究

建立了3自由度EPS系统动力学模型，提出了EPS控制系统结构，基于转矩传感器输出及其它可测信号，设计了转矩估计器来估算驾驶员操纵转矩。仿真结果表明：所设计EPS控制系统有良好助力跟随和鲁棒稳定性能。     

Dynamic correction of the steering-characteristic curve and application to an EPS control system

The steering torque of an electric-power steering (EPS) motor is interrelated with the performance of the EPS control system, therefore calculating an exact steering torque is critical in this application. This study presents a dynamic correction method that greatly decreases the calculated error in the steering torque; the PID controller demonstrated here is therefore suitable for the demands of this system. Based on an analysis of the detection process of the steering torque sensor, we first deduced that the variation of the system resistance torque equals the difference between the measured value of the steering torque and the ideal one in the previous cycle. Based on this result, we then proposed a dynamic correction method. Finally, a comparison of the simulated and experimental results for several vehicles evidenced the effectiveness of this dynamic correction method.     

Straight-ahead running of road vehicles – analytical formulae including full tyre characteristics

ABSTRACT

During straight-ahead running, the longitudinal axis of road vehicles, notably cars, is not parallel to road axis. This occurrence is general and is due both to road cross slope (road banking) and to tyre characteristics, particularly ply-steer and conicity. In order to describe such a phenomenon, the paper develops a new and relatively simple analytical model. Despite the model is linear, the solution which is provided is exact, since straight-ahead motion occurs with small angles and both the elastokinematics of suspension system and tyre characteristics can be modelled by linearised equations. The Handling Diagram theory is updated and completed by introducing the actual shifts of tyre characteristics. The validation of the analytical expressions is performed by using a MSC Adams^TM full model of a car. A subjective-objective experimental test campaign provides preliminary substantiation of the ability of the derived formulae to describe tyre performance. By means of the unreferenced analytical formulae developed in the paper, we allow, given the vehicle, the proper tyre design specification and vice-versa. In particular, a formula is given to make null the steering torque during straight-ahead driving. The derived analytical formulae may provide a sound understanding of the straight-ahead running of road vehicles.     

Integrated chassis control for a three-axle electric bus with distributed driving motors and active rear steering system

This paper describes an integrated chassis control framework for a novel three-axle electric bus with active rear steering (ARS) axle and four motors at the middle and rear wheels. The proposed integrated framework consists of four parts: (1) an active speed limiting controller is designed for anti-body slip control and rollover prevention; (2) an ARS controller is designed for coordinating the tyre wear between the driving wheels; (3) an inter-axle torque distribution controller is designed for optimal torque distribution between the axles, considering anti-wheel slip and battery power limitations and (4) a data acquisition and estimation module for collecting the measured and estimated vehicle states. To verify the performances, a simulation platform is established in Trucksim software combined with Simulink. Three test cases are particularly designed to show the performances. The proposed algorithm is compared with a simple even control algorithm. The test results show satisfactory lateral stability and rollover prevention performances under severe steering conditions. The desired tyre wear coordinating performance is also realised, and the wheel slip ratios are restricted within stable region during intensive driving and emergency braking with complicated road conditions.     

Tyre rolling kinematics and prediction of tyre forces and moments: part I – theory and method

A new method to describe tyre rolling kinematics and how to calculate tyre forces and moments is presented. The Lagrange–Euler method is used to calculate the velocity and contact deformation of a tyre structure under large deformation. The calculation of structure deformation is based on the Lagrange method, while the Euler method is used to analyse the deformation and forces in the contact area. The method to predict tyre forces and moments is built using kinematic theory and nonlinear finite element analysis. A detailed analysis of the tyre tangential contact velocity and the relationships between contact forces, contact areas, lateral forces, and yaw and camber angles has been performed for specific tyres. Research on the parametric sensitivity of tyre lateral forces and self-aligning torque on tread stiffness and friction coefficients is carried out in the second part of this paper.     

New tyre-road contact model for applications at low speed

Most of the tyre models have been developed for high speed, combined forces, etc., however, in certain tests it is necessary to know tyre behaviour at very low speed in order to evaluate different systems. So, during vehicle inspection and maintenance of the steering and brake system, by means of sideslip tester and roller brake tester respectively, the forces transmitted by the tyres are measured; all of these inspections are carried out at low speeds. Furthermore, usually, automobile vehicles run at low speeds during an important part of their operating life (less than 60 km/h), mainly during urban traffic, and in steady state conditions. Therefore, it is particularly interesting to develop an accurate model of the contact patch tyrepavement for low speeds without the complexity of models that cover a wide speed range but provide less precision at very low speeds. The dynamometer plate has proved to be an appropriate test equipment to characterise the tyre-pavement contact at low speed and the steering geometry and wheel alignment. It has the feature of being able to carry out tests with the tyre installed in the vehicle as in completely real conditions. The main aim of this research is to set up a contact model between tyre and pavement at very low speed based on the measurement of longitudinal and lateral forces. A test methodology that allows carrying out the experimental tests in a systematic and controlled way with the dynamometer plate has also been developed. From this model it will be possible to estimate the forces that tyres are capable of transmitting in different situations to act in the parameters which affect these forces and maximize them.     

Controller design for soft-disability remedy of the electric power steering system

The electric power steering (EPS) system is designed to reduce the effort exerted by driver on the steering wheel. One of the most common and critical failures of EPS is the soft-disability of the torque sensor or the loss of its signal, which leads to the instant shutdown of the EPS system while turning and causes serious traffic accidents. In this paper, a novel controller based on the self-alignment torque (SAT) estimation was designed to remedy the soft-disability of EPS system. After the SAT estimation method was verified by the empirical Magic Formula (MF) tire model, the remedy control strategy based on the SAT estimation was developed and evaluated by simulations under step and sinusoidal inputs. To further evaluate the performance of the controller on a real vehicle, experiments on a real EPS system were implemented under step and sinusoidal inputs. The results of simulation and experiment using the controller based on estimated SAT showed this controller to be feasible and capable of eliminating the abrupt reaction torque increment caused by shutdown of EPS and of remedying the soft-disability of EPS system under common input signals.     

Torque ripple minimization control of permanent magnet synchronous motors for EPS applications

This paper identifies a control method used to reduce torque ripple of a permanent magnet synchronous motor (PMSM) for an electric power steering (EPS) system. NVH (Noise Vibration Harshness) is important for safe and convenient driving. Vibration caused by motor torque is a problem in column type EPS systems. Maintaining a very low torque ripple is one solution that allows for smoother steering. Theoretically, it is possible to design and drive the motor without torque ripple. However, in reality, a PMSM system torque ripple is caused by the motor itself (saturation in the iron core and EMF distortion) and the imperfect driver. This paper analyzes torque ripple of a PMSM system, and an advanced PMSM control method for the column typed EPS system is presented. Results of the analysis indicate that the compensation current is needed in order to minimize torque ripple when a PMSM is driven.