风机塔架与叶片相互作用的数值模拟(英文)

Numerical simulations of wind turbine blade-tower interaction by using the open source OpenFOAM tools coupled with arbitrary mesh interface(AMI) method were presented.The governing equations were the unsteady Reynolds-averaged Navier-Stokes(RANS) which were solved by the pimpleDyMFoam solver,and the AMI method was employed to handle mesh movements.The National Renewable Energy Laboratory(NREL) phase VI wind turbine in upwind configuration was selected for numerical tests with different incoming wind speeds(5,10,15,and 25 m/s) at a fixed blade pitch and constant rotational speed.Detailed numerical results of vortex structure,time histories of thrust,and pressure distribution on the blade and tower were presented.The findings show that the wind turbine tower has little effect on the whole aerodynamic performance of an upwind wind turbine,while the rotating rotor will induce an obvious cyclic drop in the front pressure of the tower.Also,strong interaction of blade tip vortices with separation from the tower was observed.     

Semi-submersible wind turbine hull shape design for a favorable system response behavior

Floating offshore wind turbines are a novel technology, which has reached, with the first wind farm in operation, an advanced state of development. The question of how floating wind systems can be optimized to operate smoothly in harsh wind and wave conditions is the subject of the present work. An integrated optimization was conducted, where the hull shape of a semi-submersible, as well as the wind turbine controller were varied with the goal of finding a cost-efficient design, which does not respond to wind and wave excitations, resulting in small structural fatigue and extreme loads.The optimum design was found to have a remarkably low tower-base fatigue load response and small rotor fore-aft amplitudes. Further investigations showed that the reason for the good dynamic behavior is a particularly favorable response to first-order wave loads: The floating wind turbine rotates in pitch-direction about a point close to the rotor hub and the rotor fore-aft motion is almost unaffected by the wave excitation. As a result, the power production and the blade loads are not influenced by the waves. A comparable effect was so far known for Tension Leg Platforms but not for semi-submersible wind turbines. The methodology builds on a low-order simulation model, coupled to a parametric panel code model, a detailed viscous drag model and an individually tuned blade pitch controller. The results are confirmed by the higher-fidelity model FAST. A new indicator to express the optimal behavior through a single design criterion has been developed.     

海上风电场风机桩基局部冲刷计算

建设海上风电场时,风机所处的海洋环境十分复杂,在风、浪、流等气象水文要素的影响下,风机桩基周围会出现冲刷坑,进而影响风机基础的稳定。因此,风机桩基的局部冲刷深度是工程设计的重要参数。采用埕岛油田海洋平台桩基局部冲刷现场观测资料,对国内常用的2个计算桩基局部冲刷深度的经验公式(韩海骞公式和王汝凯公式)进行验证,运用波流合成速度代替纯潮流速度。结果表明该海域波浪对泥沙的作用不可忽略。韩海骞公式重新计算的结果与实测值吻合良好。     

Experimental study on seismic vibration control of an offshore wind turbine with TMD considering soil liquefaction effect

Wind energy is clean and sustainable. Taiwan is establishing offshore wind farms using wind turbines in the Taiwan Strait. However, these are located in an earthquake-prone area with sandy seabed conditions. To ensure their safety and reliability, the turbines’ support structure must be protected against wind, waves, and seismic loads. Tuned mass dampers (TMDs) are commonly employed to reduce structural vibrations. A TMD is more simply incorporated into turbine structures than are other energy dissipation devices. In this study, a 1:25-scale test model with a TMD was constructed and subjected to shaking table tests to experimentally simulate the dynamic behavior of a typical 5-MW wind turbine with a jacket-type support structure and pile foundation. The scaled-down wind turbine model has a nacelle without rotating blades; therefore, the aerodynamic and rotational effects due to the rotating blades were ignored in this study. A large laminar shear box filled with saturated sandy ground was used to simulate the typical seabed conditions of Taiwanese offshore wind farms. The TMD system was designed to be tuned the first-mode frequency of the test model. Two ground accelerations, selected by considering wind farm site condition and near-fault characteristics, were used for excitation in the test. The responses of the test model with and without the TMD system were compared, and the influence of soil liquefaction on the effectiveness of TMD vibration control was addressed.     

基于机舱式多普勒脉冲激光雷达测风的风速重构技术

近年来,激光雷达测风已经成为一种可靠的风速测量技术,为了在风电机组控制和监测中准确高效的使用激光雷达测风数据,需要对激光雷达测风数据进行高效、快速、准确的实时处理。目前机舱式激光雷达测风面临如下问题：激光雷达在受到来流风时会跟随机舱振动,导致实测数据波动进而对风速重构算法产生影响;激光雷达会受到风电机组叶片遮挡,导致实测数据缺失或出现无效数据。本文通过合理配置激光雷达参数,以雷达测风数据作为研究对象,对测风数据进行数值修正,消除机舱振动带来的误差,开发出一套先进先出嵌套循环判断填充算法解决叶片遮挡问题,建立线性剪切风场模型,基于递推最小二乘法求解风场特征参数,最后通过泰勒冻结湍流假说计算风轮面转子有效风速,与机舱内控制参数反演出的转子有效风速进行对比,得出两组数据相关性在0.9374,两组数据差值的标准差为0.3429,结果证明在实际应用中,使用该配置参数的激光雷达通过坐标修正和数据填充等技术手段,开发的风速重构模型算法能够准确的为风电机组控制系统提供可靠的控制输入参数。     

浮式海上风力机运动性能和锚泊系统(英文)

The development of offshore wind farms was originally carried out in shallow water areas with fixed(seabed mounted) structures.However,countries with limited shallow water areas require innovative floating platforms to deploy wind turbines offshore in order to harness wind energy to generate electricity in deep seas.The performances of motion and mooring system dynamics are vital to designing a cost effective and durable floating platform.This paper describes a numerical model to simulate dynamic behavior of a new semi-submersible type floating offshore wind turbine(FOWT) system.The wind turbine was modeled as a wind block with a certain thrust coefficient,and the hydrodynamics and mooring system dynamics of the platform were calculated by SESAM software.The effect of change in environmental conditions on the dynamic response of the system under wave and wind loading was examined.The results indicate that the semi-submersible concept has excellent performance and SESAM could be an effective tool for floating wind turbine design and analysis.     

海上风机支撑结构的时域和频域疲劳对比研究

对海上风机支撑结构进行动力响应分析,求出结构危险节点的载荷谱和功率谱密度函数,结合疲劳损伤模型和Dirlik概率模型,分别在时域和频域内对支撑结构进行疲劳寿命分析.由于时域法计算疲劳寿命需进行应力循环计数,这一过程需处理的数据庞大,耗时长.频域法省去应力循环计数,代之以概率密度函数,可相对准确、快速地计算结构的疲劳寿命.分析结果表明,采用Dirlik概率模型的频域分析法能较准确地反映海上风机支撑结构在随机载荷作用下的疲劳损伤情况,计算结果误差在可接受范围内.     

Dynamic ice loads for offshore wind support structure design

For offshore wind farms which are planned in sub-arctic regions like the Baltic Sea and Bohai Bay, support structure design has to account for load effects from dynamic ice-structure interaction. There is relatively high uncertainty related to dynamic ice loads as little to no load- and response data of offshore wind turbines exposed to drifting ice exists. In the present study the potential for the development of ice-induced vibrations for an offshore wind turbine on monopile foundation is experimentally investigated. The experiments aimed to reproduce at scale the interaction of an idling and operational 14 MW turbine with ice representative of 50-year return period Southern Baltic Sea conditions. A real-time hybrid test setup was used to allow the incorporation of the specific modal properties of an offshore wind turbine at the ice action point, as well as virtual wind loading. The experiments showed that all known regimes of ice-induced vibrations develop depending on the magnitude of the ice drift speed. At low speed this is intermittent crushing and at intermediate speeds is ‘frequency lock-in’ in the second global bending mode of the turbine. For high ice speeds continuous brittle crushing was found. A new finding is the development of an interaction regime with a strongly amplified non-harmonic first-mode response of the structure, combined with higher modes after moments of global ice failure. The regime develops between speeds where intermittent crushing and frequency lock-in in the second global bending mode develop. The development of this regime can be related to the specific modal properties of the wind turbine, for which the second and third global bending mode can be easily excited at the ice action point. Preliminary numerical simulations with a phenomenological ice model coupled to a full wind turbine model show that intermittent crushing and the new regime result in the largest bending moments for a large part of the support structure. Frequency lock-in and continuous brittle crushing result in significantly smaller bending moments throughout the structure.     

Vibration-assisted decommissioning of a slip joint: Application to an offshore wind turbine

An alternative option to the traditional grouted joint for wind turbines is a direct steel-to-steel connection, also known as slip joint. In a recently published work, a proof of concept of a vibration-assisted installation and decommissioning technique of a slip joint was illustrated. Leveraging on the obtained results, the current study shows for the first time a decommissioning campaign carried out using a vibration-assisted technique applied on a prototype hydraulic wind turbine tower located in the North Sea, and connected to the monopile through a slip joint. The key aspect of the dismounting procedure is a priori knowledge of the resonance frequency clusters corresponding to the slip joint’s cross-sectional modes. Therefore, field hammer tests and experimental modal analysis were carried out inside the wind turbine tower. The identified frequencies and mode shapes were then compared with numerical ones estimated by a finite element model of the investigated structure. The comparison showed that a set of frequency clusters can be directly selected from a detailed numerical model. The preparatory work of the slip joint decommissioning was then executed by installing electric shaker devices, based on the dynamic identification results, and hydraulic jacks mounted inside the wind turbine tower. A first decommissioning trial was carried out in May 2019, while the final decommissioning was performed in August 2019. After analysing the measurements of the hydraulic pressures, displacements and excitation frequencies during the decommissioning campaigns, the results showed that it is possible to disconnect the slip joint if, in combination to a vertical static force, one of the identified cross-sectional mode shapes is excited. The vibration-assisted decommissioning proved to be a successful technique to dismount the connection in a controlled and straightforward manner.     

Experimental field study of floater motion effects on a main bearing in a full-scale spar floating wind turbine

In this paper we present a full-scale experimental field study of the effects of floater motion on a main bearing in a 6 MW turbine on a spar-type floating substructure. Floating wind turbines are necessary to access the full offshore wind power potential, but the characteristics of their operation leave a gap with respect to the rapidly developing empirical knowledge on operation of bottom-fixed turbines. Larger wind turbines are one of the most important contributions to reducing cost of energy, but challenge established drivetrain layouts, component size envelopes and analysis methods. We have used fibre optic strain sensor arrays to measure circumferential strain in the stationary ring in a main bearing. Strain data have been analysed in the time domain and the frequency domain and compared with data on environmental loads, floating turbine motion and turbine operation. The results show that the contribution to fluctuating strain from in-plane bending strain is two orders of magnitude larger than that from membrane strain. The fluctuating in-plane bending strain is the result of cyclic differences between blade bending moments, both in and out of the rotor plane, and is driven by wind loads and turbine rotation. The fluctuating membrane strain appears to be the result of both axial load from thrust, because of the bearing and roller geometry, and radial loads on the rotating bearing ring from total out-of-plane bending moments in the three blades. The membrane strain shows a contribution from slow-varying wind forces and floating turbine pitch motion. However, as the total fluctuating strain is dominated by the intrinsic effects of blade bending moments in these turbines, the relative effect of floater motion is very small. Mostly relevant for the intrinsic membrane strain, sum and difference frequencies appear in the measured responses as the result of nonlinear system behaviour. This is an important result with respect to turbine modelling and simulation, where global structural analyses and local drivetrain analyses are frequently decoupled.     

Fluid-structure interaction and stress analysis of a floating wind turbine

In this paper, we describe a method to investigate the fluid-structure interaction of a floating wind turbine and to analyze the global deformations and the corresponding stresses with a detailed finite element model. To solve the fluid-structure interaction problem, a partitioned approach is chosen. The in-house C++ library comana, which was developed to solve multi-physic problems by coupling existing solvers, is extended to couple the fluid solver panMARE and the structural solver ANSYS. The significance of the interaction of structural deformations and the fluid loads is pointed out for the rotor of the wind turbine. In order to enable the use of a detailed finite element model in the fluid-structure interaction simulation, a model reduction method is applied in ANSYS. As a result, an efficient stress analysis can be performed under consideration of the fluid-structure interaction.     

Model test investigation of a spar floating wind turbine

Several floating wind turbine designs whose hull designs reflect those used in offshore petroleum industry have emerged as leading candidates for the future development of offshore wind farms. This article presents the research findings from a model basin test program that investigated the dynamic response of a 1:50 scale model OC3 spar floating wind turbine concept designed for a water depth of 200 m. In this study the rotor was allowed to rotate freely with the wind speed and this approach eliminated some of the undesirable effects of controlling wind turbine rotational speed that were observed in earlier studies. The quality of the wind field developed by an array of fans was investigated as to its uniformity and turbulence intensity. Additional calibration tests were performed to characterize various components that included establishing the baseline wind turbine tower frequencies, stiffness of the delta type mooring system and free decay response behaviour. The assembled system was then studied under a sequence of wind and irregular wave scenarios to reveal the nature of the coupled response behaviour. The wind loads were found to have an obvious influence on the surge, heave and pitch behaviour of the spar wind turbine system. It was observed from the experimental measurements that bending moment at the top of the support tower is dominated by the 1P oscillation component and somewhat influenced by the incoming wave. Further it was determined that the axial rotor thrust and tower-top shear force have similar dynamic characteristics both dominated by tower’s first mode of vibration under wind-only condition while dominated by the incident wave field when experiencing wind-wave loading. The tensions measured in the mooring lines resulting from either wave or wind-wave excitations were influenced by the surge/pitch and heave couplings and the wind loads were found to have a clear influence on the dynamic responses of the mooring system.     

半潜型浮式风机运动特征及系泊系统的研究

近年来海上浮式风机的研究备受关注,安全可靠的系泊系统将保证风机在风、浪、流等复杂环境荷载作用下稳定运行,准确合理地描述风机运动将为评估风机发电效率提供支持。以半潜型浮式风机的系泊系统为研究对象,基于经典悬链线理论,采用准静态分析法提出一套系泊系统的设计方法。通过坐标变换,得到风轮真实的俯仰运动用于计算风机的动力效应及评定其发电效率。采用动力法分析了系泊系统锚链的导缆孔位置、预张力大小、锚链间夹角等参数对风机系统发电效率、浮式平台运动性能和系泊锚链张力的影响,得到了浮式平台迎风面俯仰倾角、水平偏移及锚链张力随参数的变化规律,为半潜型浮式风机系泊系统的设计提供了参考。     

航行工况下自升式风车安装船强度直接计算研究

自升自航式风车安装船为海洋工程专业特种船舶,在风机运输,安装中有很高的实际利用价值。采用直接计算法,对航行工况下自升自航式风电安装船的总强度进行评估。建立了船体和桩腿的有限元建模,基于三维势流理论对波浪垂直弯矩进行长期预报,得到风车安装船在典型装载工况下的设计波参数,将船舶在设计波中的重力、静水压力、水动压力、惯性力等施加到模型上进行直接强度分析,对航行工况下船体和桩腿的强度进行了校核。本文的计算方法及结果可为自升自航式风车安装船的整体强度评估、船体结构优化提供有效依据,并且对同类工程船的设计开发具有指导意义。     

TLP型风力机的空气动力学影响及发电预测(英文)

This research proposes a new offshore wind energy generation system that uses a tension leg platform (TLP) and describes experiments performed on a TLP type wind turbine in both waves and wind. The following conclusions can be made from the results of this research. 1) In the case of coexisting wave-wind fields, the wind effect stabilizes the pitch motion. 2) The wind effect decreases vibration of the mooring lines when waves and wind coexist. In particular, the springing (2nd or 3rd order force) also decreases in this field. 3) It can be estimated that the reduction in the rate of generation of electrical power can be up to about 6% as a result of the heel angle. In addition, the annual amount of electricity generated was estimated along with the utilization factor based on the experimental results.     

南海风浪条件下Spar式浮式风机平台的构型及参数

使用WAMIT软件建立了OC3-Hywind Spar式浮式风机模型，联合FAST软件计算了浮式风机在不同工况下的幅值响应算子；结合为南海海域波浪条件优化后的JONSWAP谱，对浮式风机进行了不同工况下的响应谱分析及最大响应值计算；进一步阐述了浮式平台结构构型参数的变化对整体结构在南海相应工况下的运动影响。     

冰区海上风电基础的抗冰性能分析

海上风电基础属于典型的柔性结构。由于冰与柔性抗冰结构相互作用的复杂性,长期以来尚未形成基于动冰力响应分析的结构设计。结构抗冰设计中大都是从极端荷载出发,只考虑最大静冰力或最大倾覆力矩。基于对渤海辽东湾柔性抗冰结构的多年监测,发现强烈的冰激振动引起柔性结构的风险性要远大于极端静冰荷载下结构的整体安全问题。为了明确冰区风电基础结构的抗冰性能及抗冰设计的合理性,文章结合基于多年现场冰与结构作用观测及冰荷载的研究成果,明确该类柔性结构与海冰作用形式及其动力特性;提出了柔性抗冰结构设计中应考虑的主要失效模式及评价方法。最后,以渤海某典型风电基础为例,对其抗冰性能进行评价。该文的研究可为寒区风电基础的抗冰设计及安全保障提供合理依据。     

Study on a new method for installing a monopile and a fully integrated offshore wind turbine structure

This paper presents a preliminary technical feasibility study on a new methodology proposed for installing a monopile-based bottom supported offshore wind turbine structure. The concept is developed to address the problem of “waiting for a suitable weather window” which is commonly faced by the existing installation methods that uses a typical jack-up platform. In the methodology, a floating vessel along with a floatable subsea structure fitted with a hull on the top, hereafter named SSIP (subsea structure for installing a pile), is proposed first to install a monopile. Then the same structure is used to carry an FIUS (fully integrated upper structure) of an offshore wind turbine, which is characterized by a telescopic tower, and install it over the monopile by using an FOP (float-over-pulling) arrangement. Here, the installation methodologies are first briefly described along with the critical load cases associated with them. These load cases are then numerically studied for a significant wave height (H_S) of 2.5 m, and the results are summarized. For installing a fully integrated offshore wind turbine upper structure on a monopile foundation by the FOP method, two installation schemes are presented, and their dynamic characteristics are compared. It is shown that the proposed methodologies have potential to provide installation solutions which can be environmentally more robust compared to the existing method for installing an offshore wind turbine.     

上风向与下风向风机气动力性能数值计算分析（英文）

Although the upwind configuration is more popular in the field of wind energy, the downwind one is a promising type for the offshore wind energy due to its special advantages. Different configurations have different aerodynamic performance and it is important to predict the performance of both downwind and upwind configurations accurately for designing and developing more reliable wind turbines. In this paper, a numerical investigation on the aerodynamic performance of National Renewable Energy Laboratory(NREL) phase VI wind turbine in downwind and upwind configurations is presented. The open source toolbox Open FOAM coupled with arbitrary mesh interface(AMI) method is applied to tackle rotating problems of wind turbines. Two 3D numerical models of NREL phase VI wind turbine with downwind and upwind configurations under four typical working conditions of incoming wind velocities are set up for the study of different unsteady characteristics of the downwind and upwind configurations, respectively. Numerical results of wake vortex structure, time histories of thrust, pressure distribution on the blade and limiting streamlines which can be used to identify points of separation in a 3D flow are presented. It can be concluded that thrust reduction due to blade-tower interaction is small for upwind wind turbines but relatively large for downwind wind turbines and attention should be paid to the vibration at a certain frequency induced by the cyclic reduction for both configurations. The results and conclusions are helpful to analyze the different aerodynamic performance of wind turbines between downwind and upwind configurations, providing useful references for practical design of wind turbine.     

Dynamic responses analysis of a 5 MW spar-type floating wind turbine under accidental ship-impact scenario

Ship impact against offshore floating wind turbine (OFWT) has been identified as one of the major hazards with the development of OFWTs. The dynamic responses of OFWTs under ship impact should be taken into consideration during the design phase. This paper addresses a study on the dynamic responses of an OFWT in ship collision scenarios. Firstly, a mathematical model for external mechanism of ship-OFWT collision scenario is developed. Secondly, this model is combined with an in-house programme, DARwind, which can be used to predict nonlinear dynamic responses of whole OFWT system in time-domain. With the newly combined analysis tool, simulation cases for different scenarios are conducted to investigate the nonlinear dynamic responses of OFWT system, including the cases of still water condition, wave-only condition and wind-wave condition. It is shown that in still water condition, the ship impact will more obviously change the responses of motions and mooring system, compared with those in wave and wave-wind conditions. In the wave-only condition, these motions responses of platform are suppressed by wave effect, but the tower vibration and tower top deformation are sensitive to ship collision. For the wave-wind combined condition, the motions increment in surge and pitch due to ship collision becomes smaller than that of wave-only condition, but yaw motion has a considerable variation compared with those of the other two conditions. Additionally, the blade tip deformation increment due to ship collision are analyzed and it is found that the edgewise tip deformation got more obvious increment than that of flapwise. To further asses the safety of OFWT, the acceleration at nacelle are analyzed because some equipment might be sensitive to acceleration. The analysis results indicate that even though the OFWT structure doesn't get critical damage by ship impact, the equipment inside may still fail to work due to the high value of acceleration induced by ship impact. The research outcomes can benefit the safety design of OFWT in the engineering practice.